Thermostat Change

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

The culprit was not a heater valve, autozone thermostat and gasket was doing its job. The culprit was AIR in the system. I already bled the system after I changed my radiator, hoses, thermostat and gasket. All of a sudden my heat starts working yesterday. So after driving the car for 2-3 days after changing out the radiator and bleeding the system, I guess there was some air still in the system. I dont think my heater core is clogged but it could be? Also the car takes awhile for it to fully warm up. I put a thermometer in the heater vent and its registering about 130 degrees. I am hoping to drive it some more this week and get all the air out of the system. Right now the heat is actually pretty warm, its comfortable but not lukewarm like my early complaint nor is it blazing hot. Thanks for everyones suggestion
 
Replace the thrermostat and call it a day...

And FWIW,

Autozone thermostat = 19.99
Autozone Thermostat gasket = 15.99
Total = 35.98

Toyota OEM Thermostat = 26.00
Toyota OEM gasket = 8.00
Total = $34

The OEM Thermostat is cheaper than Autozone and I usually find that Autozone is the cheapest out of all the chain autoparts stores in my area.

I just called around and ordered a thermostat and gasket about 10 minutes ago.

Where are you getting your OEM parts from? My local dealer was charging a lot more for the thermostat.
 
OEM vendors that give MUD discounts are beno (at Lowe Toyota in Georgia) and cruiserdan (American Toyota in New Mexico), murf at Camelback Toyota in Phoenix, and maybe a few others

none of my Baton Rouge local Toyota dealers gives any discounts :meh:
 
OEM vendors that give MUD discounts are beno (at Lowe Toyota in Georgia) and cruiserdan (American Toyota in New Mexico), murf at Camelback Toyota in Phoenix, and maybe a few others

none of my Baton Rouge local Toyota dealers gives any discounts :meh:

After getting discounts from our vendors and going through shipping, isn't the price pretty close back to our own parts department from our local Dealerships?
 
depends very much what you are ordering - brake rotors, yeah, I went local considering the weight

on a larger order, the MUD vendors come out ahead by far

BTW, good to hear your solution was a cheap as letting some air out :cheers:
 
The culprit was not a heater valve, autozone thermostat and gasket was doing its job. The culprit was AIR in the system. I already bled the system after I changed my radiator, hoses, thermostat and gasket. All of a sudden my heat starts working yesterday. So after driving the car for 2-3 days after changing out the radiator and bleeding the system, I guess there was some air still in the system. I dont think my heater core is clogged but it could be? Also the car takes awhile for it to fully warm up. I put a thermometer in the heater vent and its registering about 130 degrees. I am hoping to drive it some more this week and get all the air out of the system. Right now the heat is actually pretty warm, its comfortable but not lukewarm like my early complaint nor is it blazing hot. Thanks for everyones suggestion


The OEM thermostat has a very small relief hole on the perimeter that has a loosely fitting pin. One of the functions is to allow the trapped air to pass through, That hole needs to be at the 12 o'clock position. Is it possible that the Autozone part does not have that hole or that it wasn't installed with that at the top? Eventually the air will be expelled it just takes time. If the heat output seems OK I don't think it needs to be changed now.
 
The OEM thermostat has a very small relief hole on the perimeter that has a loosely fitting pin. One of the functions is to allow the trapped air to pass through, That hole needs to be at the 12 o'clock position. Is it possible that the Autozone part does not have that hole or that it wasn't installed with that at the top? Eventually the air will be expelled it just takes time. If the heat output seems OK I don't think it needs to be changed now.

Interesting..... I'm not sure I have ever heard this. Can you post a pic?

I learn something new from MUD everyday.

Sent from my iPhone using IH8MUD
 
From the FSM:

jiggle.webp
 
From the FSM:

Ok. I'm with you now. This thread is kind of confusing from where it started but I thought we were talking 3fe's. The one pictured is vertical so the 12 o'clock reference makes sense now. The 3fe is horizontal so I was stumped at where 12 o'clock was.

I don't own a 1fz but I will file this bit of info away for a future vehicle.

Sent from my iPhone using IH8MUD
 
Does this apply to the 1fe motor as well? The 2 gasket thing. I just did my thermostat and am not getting any heat. And Its chilly here!

No. Just the 3F-E powered 80 series. The 1FZ-FE engine has a rubber o-ring/gasket that goes around the flange of the thermostat that seats it into the housing.
 
Back
Top Bottom