yooper
SILVER Star
Thanks for the reminder. I don't know why I didn't think of McMaster Carr. I just ordered from them today.
WTGDW
The Great Gazoo from 1972!
- Thread starter Hugh Heifer
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
WTGDW
Make sure to post up how they work.. my hoses are junk
- Thread starter
- #483
Thanks for the reminder. I don't know why I didn't think of McMaster Carr. I just ordered from them today.
WTGDW
It doesn't look like they have anything that fits the bill. Looks like I will go with Summit.
- Thread starter
- #484
I am designing some mounts to put a 13 inch LED bar on the front bumper. I am going to order from Steve at Southeast Overland but can't decide if I want flood, spot or a combo...
http://www.southeastoverland.com/in...ct_id=272&virtuemart_category_id=91&Itemid=33
http://www.southeastoverland.com/in...ct_id=272&virtuemart_category_id=91&Itemid=33
The LED fad will be over before you get that mounted!
- Thread starter
- #486
Got all the parts and ordered the light from Steve yesterday.
Heifer-net
Heifer-net
- Thread starter
- #487
This stuff is really nice. It is hard vinyl with the reinforcing wire but super flexible.
You can see the difference.
Heifer-net
- Thread starter
- #488
As well as how flexible it is.
So that is the 2.5 inch duct from Summit made by Dayco part 80170, defroster duct hose, Dayco autoflex.
Heifer-net
So that is the 2.5 inch duct from Summit made by Dayco part 80170, defroster duct hose, Dayco autoflex.
Heifer-net
- Thread starter
- #489
It was a bitch to get at the top but the stuff fits very well. It is a nice friction fit.
Heifer-net
Heifer-net
- Thread starter
- #490
Passenger side...
I hope I didn't dislodge any wiring with all the pushing and shoving. I had to pretty much stand on my head to get it in there.
I have about 20 inches left over so one piece is more than enough.
You should go ahead and get this stuff Aaron. It is pretty nice.
Heifer-net
I hope I didn't dislodge any wiring with all the pushing and shoving. I had to pretty much stand on my head to get it in there.
I have about 20 inches left over so one piece is more than enough.
You should go ahead and get this stuff Aaron. It is pretty nice.
Heifer-net
tucker74
Moderator
I know what I'm ordering for the pig!
Tucker
Tucker
- Thread starter
- #492
I am pleased and a bit surprised - stuff isn't supposed to work that well!
Heifer-net
yea those look good!
- Thread starter
- #494
I got the s***ty poly tank all sealed up using some sealer I got form Summit. I had to make a new pickup. Since the tank was a little warped the original one was sucking to the bottom of the tank. I made one with an AN fitting and solders some aluminum tubing to it and bent the end so that would not happen again. So it is back roadworthy again. I have not driven it much since I got the newly machined head on. Looking forward to that.
Got the front seat back in and added some velcro strips around the front zippers on the Eshan top where the zippers flap against the side of the truck a bit.
I also got my LED light brackets half built. I will post a pic of those after I knock the schlag off 'em.
And for those of you who do not know becasue you do not wander into Chat, I got my orders and have to report to Manila April 7 so the truck is going to have to be tucked away someplace pretty soon.
Got the front seat back in and added some velcro strips around the front zippers on the Eshan top where the zippers flap against the side of the truck a bit.
I also got my LED light brackets half built. I will post a pic of those after I knock the schlag off 'em.
And for those of you who do not know becasue you do not wander into Chat, I got my orders and have to report to Manila April 7 so the truck is going to have to be tucked away someplace pretty soon.
HH, safe travels to Manilla!
But no pictures ???
But no pictures ???
- Thread starter
- #496
Didn't work exactly as I planned due to the width of the light. I may trim the mounts a bit to get the light a bit closer to the bumper. I had planned to lean the mounts forward but they are right where the bend begins.
Heifer-net
justbecause
perpetually lost.
I missed where she will be while you are gone.
- Thread starter
- #498
Working a deal for storage and maintenance in exchange for driving it at beer with a guy who is just moving to Conyers, Ga...you might know him, he is kind of a parts whore.
Heifer-net
justbecause
perpetually lost.
Working a deal for storage and maintenance in exchange for driving it at beer with a guy who is just moving to Conyers, Ga...you might know him, he is kind of a parts whore.
Are you talking about one of those internet trolls?
via mobile app.
He-He-HE LOL He called him a TROLL
LOL He called him a TROLL
