suggestions for redoing brake lines

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 22, 2004
Threads
169
Messages
2,967
Location
Clemson, SC
Hey I have a 1968 single cylinder all drum brakes. I've replaced the front cylinders and a few weeks ago locked up the rear driver brake. I am gonna convert to disks in the rear and eventually the same in the front. I bought it with the front drums already screwed up so I'm not sure why they went bad and locked up. But I'm assuming old brake lines and rust in the lines. So what I want to do is redo all the lines from the Matercylinder /booster, which I'm putting in, all the way to the brakes. I looked on Spector and they are kinda high, was thinkin of just goin and measuring the lengths I needed and buying them from Advanced or Auto Zone. Any suggestions or ideas that you guys have done also.

Thanks Chuck
 
You can get metric line for the later fittings at auto stores, but not the early fittings that you have...


I have fabricated many lines from 3/16 brake line, using Toyota fittings, and double flaring the steel line...not that big of a deal..just take your time.


I have also purchased new steel lines from Toyota, and cut the fittings off, to use on new lines that I have fabricated.


Will be time consuming, and probably not going to be cheap if you want to stay with the original brake fittings, or go with custom pieces.


I would do the disc swap at the same time to both ends, and be done with it.





Good luck!


-Steve
 
Here is my thought. I'm gonna go with monte carlo calipers in the rear. So I'm thinking if I were to buy lines from autozone, the only cutting and refitting would be done at the cylinder end? Am I correct. Cause I'm not worried about stayin stock on the lines. Too much of a PIA for my uses. I've got a lead on parts for a front disk brak so I gotta find out what brand it is to find out what kind of cutting and flaring I have to do. But I believe I can use the same size lines through out the truck and only have to replace and reflare fittings at the calipers or at the cylinder. Does this sound right Steve, thanks Chuck
 
You are on the right page...but you are not going to find one line that will reach all the way from the master to the 'T' fitting where the rear line will split to feed the calipers...unless you purchase a 25' roll of brake line, and flare one end, route it, and flare the other end...but trying to figure in frame flex from where this line will transfer from the body to the frame, and trying to route a 15'+ line would not be a good idea...and would look like crap.


-Steve
 
i fabbed all mine as well, take you r time, measure twice then bend, its tricky at first but always easy to bend back and try again.
 
oh yeah make sure you have a decent flare tool, autozones is a piece of SH&*, invest in a good one. youll thank me later
 
Let's see if I've got this right...you're gonna run drums in front, disks in rear, with home made brake lines in between? You planning on putting your kids in this car? Seriously, unless you intend to drive around in reverse all the time, you really want to re engineer your project...
 
Thanks VT...and booger buy a pair of glasses if you don't already own a pair. To enlighten you booger it's less expensive to do a rear brake disk conversion using montecarlo calipers etc. then it is to put Cylinders and drums back on. Also I just rebuilt the front ones so I know they are in good shape. The culprit is more than likely the brake lines. SO I am gonna make my own brake lines but if I do it correctly I am only gonna have to cut one or 2 lines and put on new threads to fit the master cylinder and maybe the front brakes depending on the route I go. I may flare them myself, if not I have a good mechanic down the road that has flared some for me before that I broke when I was redoing my front ones. And I'm not claiming to be a master mechanic but I'm sure as hell gonna do a good enough job so that when I or any passengers get in my cruiser we are gonna be safe. So get your facts straight before you start insulting fellow cruiser heads on how they are gonna work on their cruiser. You won't get much tech help if you continue.
 
Thanks Cam for the input...I'll definately be drawing it out on some paper with those measurements...brakes lines = expensive...lol.

Later Chuck
 
CruisinTiger said:
Hey I have a 1968 single cylinder all drum brakes. I've replaced the front cylinders and a few weeks ago locked up the rear driver brake. I am gonna convert to disks in the rear and eventually the same in the front. I bought it with the front drums already screwed up so I'm not sure why they went bad and locked up. But I'm assuming old brake lines and rust in the lines. So what I want to do is redo all the lines from the Matercylinder /booster, which I'm putting in, all the way to the brakes. I looked on Spector and they are kinda high, was thinkin of just goin and measuring the lengths I needed and buying them from Advanced or Auto Zone. Any suggestions or ideas that you guys have done also.

Thanks Chuck

Hold your horses.. check NAPA before anything else ... they have them
I redid all my lines and they are cheap..I mean all of them including the ones inside the engine bay from the MC you will have to bend some because they are too long since they sell them in several stock lenght 8"-12"-48" etc..
I have a bender but I found that a small section of pipe is more practical to make quick bends or coils
 
i just redid mine with drums in the rear w/ 3/16 line. Anywhere there were metric fittings i just cut and flared and used the old fittings. A flaring tool is cheap and with the extra line you cut off just practice. Commonly it's cheaper to buy the tools yourself and do things instead of having others do it for you. Summit also selld lengths of brake line so depending on your setup with how many metric fittings you have it may be cheaper to buy the line and bend it all yourself and use existing fittings.
 
I replumbed my 12/69 using all junk yard parts. Took the lines off a mini truck for the firewall, fit perfectly on my cruiser. I tied the rear system into the existing system that spans from the firewall back, I just replaced the fittings. I also used the booster and master off the mini, but I’m running drums in the back and you probably want a 1" bore master with discs in all 4.

Oh, and all of my brake lines, fittings, brake line extensions cost me a whopping $6. Booster and master was $30.
 
I agree with doing the brake lines yourself, it is easy and cheap, just requires some thinking. Easiest way to figure out fittings is to take one of the blocks from the axle and match the fittings to it, then buy sections. Good luck.
 
I've used mini truck front lines before, they worked well with a little bending and didn't really cost anything from the junkyard. Eventually, I just redid all of the hard lines on my 55. Bought a role of 3/16" and some ends from vatozone. They do have a tool that works good for double flaring. The SAE tool is s***, absolute s*** and improperly sized for that line. The metric double flaring tool they loan out works great, but you must use the 6mm tool for the single flare, and clamp down really tight. Wrapping the line a few times around a pipe or a full beer can for flex joints also will look really good if you take your time.

Or buy new line from toyota for a later model 40, they are not too overpriced.
 
My sincere apology if my comment was insulting. That was not my intent, and I admit there must be better ways to get someone's attention, which was my intent. Consider me doused. I've seen the Monte Carlo caliper set up, and yes, it is a quick, inexpensive conversion. My point was that in using a pair of front disc brakes on the rear end, and drum brakes in front, even if you eventually will convert to all discs, the proportioning of the hydraulic pressure to the wheels is unbalanced, in effect having the stronger brakes in the back. No big deal when offroading at low speeds, but it could pose a hazard in freeway traffic.

BTW, you mention needing new fittings. What I found out when rebuilding mine was, the Toyota master cylinder has two thread pitches, one for the front circuit, another for the rear, I guess that's so the lines can't be fitted improperly. The single circuit line and fitting on your '68 should fit one or the other, so you'll have to identify the right thread pitch for the one remaining, if you're using a Toyota MC. Also, the Toyota Body & Chassis manual will give you the clearance between the MC piston and the booster pin, which you'll need to set the free play between the booster and MC, which should be adjustable.
 
Yeah Poldo that's what I was planning on doin was buyin the lines with the ends already on them. I'll have to do some retrofiting using the monte carlo calipers in the rear and the stock drums in the front. No big deal just a little thinking. Thanks Snail for the flex joint idea wasn't sure how I was gonna do that.
 
Back
Top Bottom