stock wiring

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

cool cool. so basically if I were to restore a harness in the future i would probably get replacement wires on the ones that were cracked and old and put silicone grease n them and wrap them in electrical tape and im sure they would be good for another 20 years or more.
 
IDave said:
The OEM harnesses I've unwrapped clearly have some sort of silicone grease or similar material under the electrical tape.

Yes, it was a sticky mess, but I thought that was simply sticky tape, since I could only find it on the outside of the wire bundles not between the wires.
 
You might be right, Claudia. Old, broken down tape adhesive. But deep in some of the harness it felt oily to me. Wouldn't hurt to put silicone in there, would it?
 
big thing that seems to kill them is corrosion and heat as IDave said.

I noticed that I had to be real careful with the heat gun on stock wiring. I didn't replace EVERY wire.... and when I used the double wall polyolefin shrink with internal adhesive, the factory wire would start to brown and burn easily. I could leave the gun on the SXL wire all day w/o any issues.

THIS in itself tells me that the new SXL wire might never have the heat/elements issues that the factory wiring did.

however.... to be sure, I wrapped all the external/engine bay wire (and what I could for the internal/cowel harness) in hi-temp corragated loom and sealed it all in with Super 33 tape
 
A plug and play harness would definalty be worth more than Painless or who evers generic harnesses IMO.
The PO had a painless put in my cruiser, but the shop did a hack job at best. I'd really like to rewire it. There are sections of wire with as many as four crimped connectors in three or four feet. I think the only thing that was ever wrong with the original wireing was things breaking off right at the connectors. So the harness does nothing for that, plus I have a million unreliable crimps that are not sealed at all. Once I figure out how to put new leads on all my lights and switches ect, I'd like to put it all back together with weather packs, but that will certainly require that I make a good schematic, since they could go together wrong that way.
 
what i would eventually want to do is replace bad wires with new ones with the stock color only for things like the headlight harnesses and stiff i would upgrade to a type of wire that would except h4s and higher output bulbs. Using that as an example.

so you got your wire at waytekwire and delcity ? is that a website or a local store near you?
 
IDave said:
You might be right, Claudia. Old, broken down tape adhesive. But deep in some of the harness it felt oily to me. Wouldn't hurt to put silicone in there, would it?

I don't think it would hurt; unless you want to get the wires apart again at some point ;) I got a Painless system now, although in hindsight, the main trunks of the harness were o.k. I also kept the connections directly at the switches and connected to the new harness via vibration and water resistant connectors.

I don't think it is the age of the vehicle per se that makes the wiring fail, but rather what happened to it. Even in our 45 yr Buick, the stock wiring works fine, as nobody ever messed with it. However, on my cruiser, a cruise control and trailer wiring, stereo system and other accessories by various POs wreaked havoc.....:frown:
 
I rewired my truck (1981 FJ40) including the emissions with the painless kit... I didn't know better yet. It was by nomeans painless, but it also wasn't designed for the truck either. I drew out a full sized floor model of the truck, including the frame, on corrugated plastic in the garage and labeled all the connections and spaced them accordingly on the diagram to get the basic lengths of wires, then I mocked up a full sized true to life dashboard including the space from dash to firewall as this area is the most complicated in my opinion.
Anyway, I listed all the stock wires colors and matched them to the painless kit then used the additional wires (such as electric fan wire and A/C wire etc and fit those to things such as the charcoal canister and carb cooling fan) Itis time consuming, but I would be happy to take some time to post the list and I'm also working on the schematic (anyone know a good program for this?).
I must say, it looks stock, minus some of the connectors.
 
DSRTRDR said:
I don't think it would hurt; unless you want to get the wires apart again at some point ;)

I was thinking in terms of silicone wax, not silicone caulk!:D
 
FWIW, I bought a 21 circuit kit from EZwiring.com. Quite easy to install, wires labeled every 5 inches or so (no need for a magnifying glass and manual for future troubleshooting) and I think it only set me back $160. I merely cut the plugs off my stock harnes and soldered/connected them to the new harness so I can just buy factory switches and stuff as needed and plug 'em in.....

Tym
 
DSRTRDR said:
I don't think it is the age of the vehicle per se that makes the wiring fail, but rather what happened to it. Even in our 45 yr Buick, the stock wiring works fine, as nobody ever messed with it. However, on my cruiser, a cruise control and trailer wiring, stereo system and other accessories by various POs wreaked havoc.....:frown:

I do agree when it comes to the INSIDE of the vehicle. The reason I pulled the cowel harness is because I was chasing a PO short that I couldn't figure out. There were some mightily melted wires INSIDE that harness that I would have never found had I not pulled it and unwrapped it....
The cause you ask????? ...... the lighting circuit is R/B 12v+ and W/B ground. they are terminated in opposite end bullet connectors.

....... this is what I found :mad: might cause a problem???


anyway.... the rest of the harness that was unaffected by THIS crap was fine :rolleyes:

however..... everything that was outside the vehicle (engine bay, and rear frame) was in various states of corrosion and brittleness.

If left alone and unmollested by wire snips, the main inside harness would probably be fine. On the other hand, these vehicles gat a LOT of moisture under the dash.... the connectors would probably still corrode. I did address that though earlier in the thread :D easy enough to take care of!
short culprit.webp
 
IDave said:
I was thinking in terms of silicone wax, not silicone caulk!:D

dielectric grease is what you're looking for.

I don't see it causing any issues, but once it's on there it's slippery and would probably make wrapping it in tape fun as the tape wouldn't stick :D
 
That makes sense.

I had a LOT of wires like yours in my underdash harness, and the harness had also blown open! (then the PO painted over it. :D)
 
I have to unpack it and stretch it out to figure out which end is which. Looking at it quick the other day it may not have all the switches. I saw heater and flasher switches for sure. I didn't see anything that was cut or spliced. I'll check it out in detail and maybe take a picture or two.
 
yeah 2owners ago my truck got painted red and some of the wires to. I claim this to be some of the reasons why some of the wires are cracking and getting brittle.
 
Back
Top Bottom