Soldering Defogger?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 3, 2006
Threads
53
Messages
1,727
Location
Laurentians North of Montreal, QC
Hey Folks,

Just wondering if anyone has ever tried soldering defogger lines. I'm not talking about the paint stuff, but solder.

It must be possible, because the connectors are invariably soldered.

I have a cut main strip (not a central line, the strip at the side of the window) that I'd like to repair permanently and I have found in the past that the paint stuff is not that great (tends to come off).

Before I actually attempt it, I thought I'd ask anyone who's attempted it before, what are the risks of cracking the glass from heat stress?

Thanks,

Chris
 
I would also be concerned about damaging the tinting. I did use one of the defogger repair kits on another car once before for the horizontal defogger line, it's a conductive paint, it seemed to work.
 
I just looked up repair kits. Found one from JC Whitney for $20. Frost fighter. Is there a recomened product that works better than others?
There is also a tab repair kit. fwiw.
Chris

Any details on that tab solder kit? Instructions on how to do it?
 
I have repaired a couple. I've used the conductive epoxy or super glue type without success. The tab cracked right back off. I was successful at soldering. I took the car outside on a real sunny day so the glass was already pretty hot. I tinned both surfaces and went for it.
I regularly use a torch on windshields without incident but remember high school auto shop where we'd hit all windows with a torch and then leave thew scene and wait a while. After a few minutes all the windows would explode in succession:D

Good luck
 
I have repaired a couple. I've used the conductive epoxy or super glue type without success. The tab cracked right back off. I was successful at soldering. I took the car outside on a real sunny day so the glass was already pretty hot. I tinned both surfaces and went for it.
I regularly use a torch on windshields without incident but remember high school auto shop where we'd hit all windows with a torch and then leave thew scene and wait a while. After a few minutes all the windows would explode in succession:D

Good luck

Thank you, 619TOY, :beer: that's exactly the type of answer I was looking for :)

I'm going to use a very low temperature solder (a type of lead alloy used in industrial fire hydrants heads that melts at 90 degrees celsius or thereabouts). I guess a hot air gun to preheat the area on both sides of the glass should do it.

your anecdote about the exploding glass is consistent with differential expansion of inside versus outside on tempered glass - one side hot, the other cool = excessive strain that would exceed the surface tension limit and cause it to explode suddenly...

Thanks for your experience, I can now see how it can be done. Thanks again!

Chris
 
I haven't used the product but here is the link to the site. I think i'm going to get the grid repair kit. They have the tab kit as well. http://www.frostfighter.com/ff_products.htm


Chris
Thanks, Chris, I will sure take note of this, they seem to offer a full line of products. Like that website, straightforward... In the meantime I will practice my soldering skills on the old 60's rear glass ;)

Chris
 
OK so almost a year later (yeah... First frost last week) I thought I'd add the conclusion to this:

The paint on stuff works for defogger lines, BUT you have to lightly sand the varnish off the conductive metal deposit so it may actually conduct on some resistive compound.

If it doesn't work, you probably missed a very fine hairline scratches. I did and with a strong flashlight at night exposed the offending scratches from behind. It looked perfectly fine otherwise, but a hairline cut across the main wire was enough to completely render part of the defogger non functional.

One other thing: it tends to defog more where it was repaired, possibly because the repair is more resistsive at that location (hence higher power output by the principle P=R(I^2)). You may need to lay down a few coats of the stuff for it to be truly effective.
 
Hmm, so you sanded the defogger line a bit, eh? Any help on how deep you sanded, like was the layer of varnish a yellow/amber and then you could literally see the gray metal under it, or a reddish color under it? I ask because I laboriously used a Toyota factory kit last year and got zero results. Did not help a single bit. So your varnish comment has my full attention. I'd love to fix it as frost season has arrived.

Thanks in advance,

DougM
 
Funny you should ask... I guess it's simple intuition... Because I tried before without doing this sanding and it didn't work either... So just like you I figured, since the lines looked red from the outside and much darker on the surface inside, it could simply be some varnish or oxidation so I used some fine wet and dry sandpaper (I guess that was 1000 grit) and very lightly rubbed the material and it became silvery right away... Then I painted the coppery repair stuff stuff on it a couple of coats and voilà, it works now :)

If you are doing that to a line in the middle of the glass, I would suggest you use some fine steel wool instead, as sandpaper scratches glass.

To identify the break I used a strong light from behind, as you only need a hardly visible, hairline cut to render de affected defogger line(s) useless...

Since the copper paint is not very nice to look at I used some tape to mask the areas I didn't want to cover, so it would not be visible from the outside. I guess you could paint some dark lacquer on top to go with the other lines, if you're a stickler for detail :)
 
If it's not working at all it could simply be a blown fuse or perhaps tripped relay (forget which). If OTOH it works but only some lines, it's definitely a break in the conductive film.

Hope it helps and good luck finding the break if any, they can be very hard to see, use a strong flashlight from behind the trace itself. The break could be as thin as a hair...
 
Thanks for the tip. You may have saved me the pain of replacing the rear hatch glass.

DougM
 
Wow, I'm really happy I could be of help for a change, after all the help I got from others on this great forum :)
 
Back
Top Bottom