Shackle bushing help.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 8, 2013
Threads
15
Messages
138
Location
Utah
Way excited to receive some new HFS grease-able shackles and bushings. I started the install and it is not looking right to me. Been a long time since I've done this. The new bushings stick out about a 1/16" on each side, the shoulders are not in contact with the hanger or spring. They do fit snug within the shackle.
If i continue with the install without addressing this will it be damaging or reduce the performance?
2qY2CEFWSFCRsH00wsNuzA.webp
G54OcKwcSK6OrU7ThSo89A.webp
 
bushings should be flush, you can cut a section out of the middle for the correct length but the shackles are too wide they should fit snuggly against the shoulder of the bushing.

or just return all and get the correct stuff.
 
bushings should be flush, you can cut a section out of the middle for the correct length but the shackles are too wide they should fit snuggly against the shoulder of the bushing.

or just return all and get the correct stuff.

Thanks @3_puppies.
Bust! I had a feeling that was the answer. I was just hoping to get it together soon. But I definitely want to do it right. Reading through alot of the info on MUD, it seems like HFS is not a preferred suspension brand.:frown: I'll give em a call and see if if we can't right the ship.
 
I didn't see a mention of what year your vehicle is, is it possible you were shipped a later year set and have an earlier vehicle. Later vehicles have larger pins and and probably longer bushings.

If they're not going to help you resolve this there is another option as a last resort of sorts. Measure your frame brackets outside to outside and your new bushings inside the flange to inside the flange. Now subtract the frame bracket dimension from the bushing measurement which will give you the difference. Now cut the difference off one of your bushings for each location. Your bushings will now fit up against the frame mount.

Now your shackle is going to have a gap between the bushing and the shackle that needs to be filled. Measure this gap and divide by 2 which will give you how thick a fender washer you'll need for each side to evenly space the shackle. Depending on this measurement you may get by with a hardened fender washer on each side as they are generally thicker than standard fender washers. If not then go to your local bolt store and buy a box of standard fender washers that fit the pins/bolts and stack them until you get the correct spacing. If it doesn't work out with an even number on each side it will still work you just need to remain consistent as to the same washer count on the same side.

This may not be ideal but if you don't have the money to buy all new parts with the correct fit it will at least keep you on the road.

If you are going to buy new hardware, this is my recommendation:

Ironman 4X4 anti-inversion shackles

IRON-343LH__15967.1513017628.1280.1280.jpg


They also make the pins as well.

Greasable_Pin__64668.1466123736.1280.1280.jpg


I like these and bought them because they provide protection for the zerk fitting so they don't get sheared off if rough 4 wheeling.

They have you covered for bushings as well.

Bush_Kit_2016__12448.1466140607.1280.1280.jpg
 
I had the opposite issue with HFS. I couldnt get the shackle on as it was too tight. Bushings were fully seated. I had to take the bushing to the grinder. I am happy with the way it rides, but it wasnt a plug and play suspension kit by any means. I bought a good bit from CCOT and they always treated me pretty good with issues. A bit unconcerned with the suspension issues, but maybe my tone wasnt the best.
 
The Mark’s Off Road Double Duty Shackles are ALWAYS the right width. ;)
 
Thanks gents for your input. I spoke with CCOT. After some discussion, (including their offer for full refund/return) the solution i'll try is to trim the interior portion of the bushing and use a hardened washer between the shackle and bushing to fill the gap. I (and Manny at CCOT) don't think this will have a negative effect on performance. I'll post up some photos of the solution. For now, I've got to hunt down the washers.
 
If it were me I would return them and order a set from Kurt. You will have them in 2 days and I bet they will work. No excuse to have to grind and use washers. I just did my 62 this week with Kurts stock bushings and greasable shackles. Shipped from Utah to SC in 2 days! Zero install issues.
 
The more i think about this, the more I realize you guys are right. I've been spending a lot of time fixing a bunch of my old half a@# repairs from being poor or stuck in the woods. Time to do it up right! I would like to point out the product doesn't seem poor, just not the right fit for my 69 40. I'll take CCOT up on their gracious offer and give Kurt a call.
Thanks for letting me bounce this off ya! :beer:
 
It strikes me as odd that after several years of marketing a shackle with an adjustable gusset SPECIFICALLY DESIGNED to avoid this issue, it rarely gets any attention unless I focus some there.
 
It strikes me as odd that after several years of marketing a shackle with an adjustable gusset SPECIFICALLY DESIGNED to avoid this issue, it rarely gets any attention unless I focus some there.



Mark, could you post up some pics, specs of your shackles for all of us to see? I am looking for some longer than stock shackles for the rear of my 40, something about 4-4 1/2" from eye to eye.


If this isn't the place to do it no problem, we could post it up in my build thread.
 
Ryan and all

Here is a link to my specials page. Shackles are listed under section 130.

http://www.marksoffroad.net/1specials/1specials.html

Unfortunately, the pic link is not working. Further, the description needs some polishing since when I wrote it in 2009. Fortunately, my daughter JUST gave me the info to do major revisions of pics and text on the website, so I will work on this...as soon as I get through all the orders.

With my search skilz, I could only find ads for them in classifieds. Maybe I need to do a thread infomercial here in tech, although I think the adjustable gusset should be self-explanatory.
 
Mark, FWIW I joined MUD in 2015 and this is the first time I have ever heard of this product you offered. I completely understand, as my business has been in the same town since 1966, and about a year ago someone said "Never knew you were here". Shocked me at first, but made me think about how people find me, especially people that are new to the community.
 
Exactly why I was asking Mark for more info, not everyone knows.
 
I'm chiming in a bit tardy here, but this sure smells like the difference between 1980 and 1981 springs/bushings, i.e. wider 1981-newer bushings being supplied for a 1980-older rig ???
 
OK. So I took a newer pic, and with my 3rd rate hacker skills I managed to write enough code to replace the pic on the specials page. but the link to view the photo won't work, so here it is :
130-shackles.webp
 
Back
Top Bottom