Seized Motor -- What next?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 7, 2017
Threads
22
Messages
221
Location
New England
So... was driving home in my FZJ80 and I think it overheated and seized. I just put a bunch of money into it, so I hate to think it's just scrap metal. What should I do, reman 1FZ-FE? LS swap? Something else? If I do an LS swap, does anyone sell a turn key package that'll give me all of the mechanial and electical parts I need such that I could buy a crate LS and drop it in?
 
I was driving home from work. On the interstate. Noticed a funny vibration, realized it was misfiring. Thought it was odd, then realized it was running warm (not into red zone, but just below) and was seeing some smoke. Was in a construction zone with no easy place to pull off. Slowed down, temp dropped a bit, drove it until next off ramp. Shut it off. Popped hood, coolant bottle full, but coolant was everywhere, not clear where it was coming from. Let it sit for 5 minutes or so. Put key to on position, temp was back down. Went to start it, sounded like it was going to start, then sounded like starter couldn't turn motor. Turned key to off. Turned key back to start, wouldn't crank at all. At this point, decided to have it towed to shop.
 
when something very similar happened to our LX, we got a new short block and had "Tools R Us" rebuild the entire thing - needless to say, it cost a pretty penny (not for the faint-of-heart) and I now have stated-value insurance on it to reflect the expense for the new motor

the alternative would have been to get a good used motor from arcteryx=CruiserYard - I just didn't want to deal with the logistics of shipping and such
 
Sounds like scrap metal..

Ls turn key sounds like 30k.....
Cheaper if you do it yourself.. 15k?

Edit. Sounds like your head gasket.. had to say it
 
I've been doing more reading, seems like HG failed, and then it hydrolocked. Assuming it turns over after pulling plugs, how do I tell if I bent a rod? Does the head have to come off to determine this? Seems like minimally I'll need a new HG and then possibly need head machined if it warped (or new head if it's way out).
 
I've been doing more reading, seems like HG failed, and then it hydrolocked. Assuming it turns over after pulling plugs, how do I tell if I bent a rod? Does the head have to come off to determine this? Seems like minimally I'll need a new HG and then possibly need head machined if it warped (or new head if it's way out).


You can check it with the head on using a micrometer and equipment from a machine shop down through the spark plug hole. The correct way is with the head off and a straight edge across the block and use feeler gauges to the top of the piston or to use a micrometer that indexes off the top of the block to the top of the piston. Must measure ALL to get the comparison.

Hopefully your starter doesn't have enough oomph to bend a rod in a hydrolocked condition on these. I know a small block Chevy DOES. BTDT twice.
 
I've been doing more reading, seems like HG failed, and then it hydrolocked. Assuming it turns over after pulling plugs, how do I tell if I bent a rod? Does the head have to come off to determine this? Seems like minimally I'll need a new HG and then possibly need head machined if it warped (or new head if it's way out).

Where are you located?
 
Threads like this make me scared to let my wife drive my truck.
 
Truck is at my buddy's shop. Engine was hydro locked, is turning OK now. Likely going to have him pull the head and with any luck everything is good and can just do HG. Priced out some turn key LS conversions, but not ready to pull the trigger yet due to price. Still looking around for someone that'll do it on the cheap or someone who was going to do a conversion and changed their mind and has all the needed pieces.
 
I think proffitts will do a LS swap for about 20k last I heard. I think that's with a used 5.3 motor. If your gonna keep it for another 5plus years pony up the cash for the LS. If less than 5 years just fix the 1fz. That's my opinion. 80 with a LS is awesome. 300+ hp and nearly 20mpg. And proffitts does good work.
 
well, given what just happened I would relace the HG (check block and head / get machined, valves, all the PM while in there).

I wouldnt bother with an LS swap but thats just me, given what youve already stated in this thread, just seems like a big money/energy vacuum for you.
 
Hopefully your starter doesn't have enough oomph to bend a rod in a hydrolocked condition on these. I know a small block Chevy DOES. BTDT twice.

The rods on these are pretty stout though. I forget who posted it, but someone posted a pic of a rod out of a 1FZ-FE vs. a Chevy(?) rod that came out of a motor that was putting out 800hp. The Toyota rod was at least twice as beefy. Seems like it would take an enormous amount of force to bend one, but I suppose it's possible.

That said, if OP is looking for the cheapest option, I would say buying a used motor and tossing it in would be the way to go. Otherwise, it just makes sense to do a full head job and WYAIT stuff which can get expensive, but it also makes sense to do if the plan is to keep the truck for the long haul. Assuming the bottom end is OK, of course. A full rebuild is going to be very expensive, but still probably half the cost of an LS swap.
 
My rig is a '96.

Yeah, my plan at this point is, have the head pulled. If bottom end is fine and head is not warped beyond machining, going to have head rebuilt and then address anything that needs doing while head is off including tough to get at coolant lines, etc.

If the head is not serviceable, not sure what I'll do.

If the bottom end is done (seems highly unlikely), I'm going to do an LS conversion, but won't be doing it right away, just will park it in the garage for a while until I have a solid plan.
 
Back
Top Bottom