RTH: knuckle rebuild, axle/birf concern

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 20, 2010
Threads
64
Messages
580
Location
Central NJ
Hey all,
So I started tearing into my axle maintenance project today in preparation for the rebuild this weekend. I bought a kit from Onur and got everything except new inner axles and birfs. I had no clicking whatsoever so I was confident (over-confident?) that my axles would be fine.

It's a 97 40th Ann. that I bought from a Mudder a few years back with around 150K miles. It had the knuckles redone right before i got it, and it's got 211K miles now.

The picture show the birf pretty much how it came out of the truck. It was by far mostly gear oil behind the hub. I was optimistic when looking in the hub - nice grease in there and look good. However, going further showed the inner oil seal was toast. I barely touched it and a piece of it fell off. The pic below shows is after a few wipes with a paper towel. Crazy. This is the DS, I have not touched the PS.

So a few questions/concerns:

1) See the scoring on the axle? You can feel it as well. So I need to order new axles. I just found out that Onur is out until July 10 (congrats @beno on your honeymoon BTW!) so I unfortunately need a new supplier for these axles ASAP.
---> Can someone recommend another parts vendor? Is @cruiserdan still in the game? I thought I read a thread stating that he is not, but I've mainly been lurking in the 40 Tech section these days.

2) Please look at the birf. What's with the discoloration? Should I order new birfs based on what you're seeing here?

Thanks!

IMG_0297.webp
 
The "discoloration" is heat treatment. The passenger side inner will probably not be as worn since the shaft is shorter and does not deflect as much. That one still may seal with an OEM seal, especially if you adjust the seating depth a bit.

Yes, I put my parts cleats in the display case a couple years ago. I now hang out at the Land Cruiser Heritage Museum.
 
I'm as loyal as anybody to Toyota OEM, but … these seals from Marlin rock.

HD FJ80 Inner Axle Seal | Marlin Crawler, Inc.

The Marlin seals have been known to leak worse.

The shaft doesn't look too bad. I would buy oem seals and just change the depth. Then just monitor the fluid and grease level.

You could go rcv axles or buy used shafts
 
How does one adjust the depth of the inner axle seal, and ensure it's uniformly perpendicular/sealing with the sealing surface on the shaft? I've seen people recommend putting the seal at a different depth, I just can't picture how to do that.
 
How does one adjust the depth of the inner axle seal, and ensure it's uniformly perpendicular/sealing with the sealing surface on the shaft? I've seen people recommend putting the seal at a different depth, I just can't picture how to do that.

You don't pound it in all the way. If in doubt the wits end tool is great and inexpensive. He did all the guess work for you.
 
You guys are great. And @beno came through. New OEM axles ordered. Boom. Should be here in about a week or so. Gives me time to go all OCD and clean everything up.
dont put birfs in the dishwasher AND expect to use for dishes ever again, ask me how I know........................
 
Hey all,
So I started tearing into my axle maintenance project today in preparation for the rebuild this weekend. I bought a kit from Onur and got everything except new inner axles and birfs. I had no clicking whatsoever so I was confident (over-confident?) that my axles would be fine.

It's a 97 40th Ann. that I bought from a Mudder a few years back with around 150K miles. It had the knuckles redone right before i got it, and it's got 211K miles now.

The picture show the birf pretty much how it came out of the truck. It was by far mostly gear oil behind the hub. I was optimistic when looking in the hub - nice grease in there and look good. However, going further showed the inner oil seal was toast. I barely touched it and a piece of it fell off. The pic below shows is after a few wipes with a paper towel. Crazy. This is the DS, I have not touched the PS.

So a few questions/concerns:

1) See the scoring on the axle? You can feel it as well. So I need to order new axles. I just found out that Onur is out until July 10 (congrats @beno on your honeymoon BTW!) so I unfortunately need a new supplier for these axles ASAP.
---> Can someone recommend another parts vendor? Is @cruiserdan still in the game? I thought I read a thread stating that he is not, but I've mainly been lurking in the 40 Tech section these days.

2) Please look at the birf. What's with the discoloration? Should I order new birfs based on what you're seeing here?

Thanks!

View attachment 1723873

It is the inside of the bird that suffers from wear.
 
Redeye, If you are really worried about reusing that worn axle, for less money then the cost of new a one, you can easily repair the damaged one. You just need to install a Speedi Sleeve over that worn spot. Below is a link that will tell you how Speedi Sleeves work, and how they are installed.
SKF Speedi-Sleeve
 
How many beers in before the dishwasher looked like a good option?
single, no kids ,usually on the road, so no beers needed straight to dishwasher................
 
Back
Top Bottom