Routing PCV

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
284
Messages
8,118
Location
Kansastitty
I am about to install a 2F to replace my '74 F. The F has the PCV coming out ofthe forward side of the inspection cover. The 2F has it coming out of the rear of the inspection cover. I want to continue to use my '74 carb and the PCV hose currently attaches to the insulator at the base of the carb.
Here is my question, can I run the PCV into the intake manifold or should it still go to the base of the carb?


Ed
 
Hey Ed,
I dont see a difference in running the PCV valve to the intake or the base of the carb, either way it is going to the same place(correct me if I am wrong). I say just run it from the base of the carb like you already have it and call it good. :)
 
What is the issue with using the insulator? If you don't, you'll have to plug it. Why not run the hose into it?
 
Well, if I use the 2F inspection plate, the hose comes from the rear of the motor instead of the front, which makes routing of the hose unhandy. I can't turn the insulator around to face the rear due to interference with the carb linkage. I was going to machine an insulator out of aluminum with no port and just connect the PCV hose directly into the intake manifold right below the carb.
I think I should be ableto use aluminum because I have a header and am not heating the intake with hot exhaust gasses.



??????


Ed
 
Hmmm...do you have to use the 2F side cover? Couldn't you use the cover from the F engine? I built a mostly 2F but kept my '74 head/carb/intake manifold, used the F side cover and usual PCV hose route.
 
Yeah, that is an option and I may end up doing just that. I mainly wanttoknowif anyone sees a problem with running it into the intake, and I think the answer to that is "no".

Thanks,

Ed
 
depends on where into the intake you run it. I would not run it to one of the individual runners, instead only to the common plenum area. it does introduce oily vapors into the intake tract and would most evenly distribute these to the cylinders if located in the insulator, or in an area of the intake plenum just below the carb opening.
 
At first I was thinking of the closest, but had the same concerns. I have a manual MC, so I think I'll use just the port in the center where you suggest.


Thanks,
Ed
 
Ed, guess where the 2Fs plumb the PCV from the factory? Into the intake manifold! :bounce:

Just use a central vacuum source like cruiserbrett said.
 
Thanks all. I'll use that centered hole right below the carb.

Ed

We got the head on, valve train, so its pretty much done. I'm going to have the valvecover beadblasted then PC clear....just for a little 'bling'.


Ed
2F 001.webp
2F 002.webp
 
Did you sandblast that block? What color are you going to paint that?
 
The head and block were "steelabraded", came out looking like new castings. I wondered what to paint it and the consensus was "don't paint it black, because you can't see any leaks" so I painted it Plastikote Cast Iron Gray. Takes 600* and is resistant to most fluids. We'll see, but of course I WON'T HAVE ANY LEAKS...hehehe. I painted all the tin with Rustoleum Satin Black.
Bored .030 over, new pistons and rings, new cam and lifters, polished the crank, new Toyo bearings and gaskets.
I'm "shakin' like a queer at a hotdog stand."


Ed
 
Damn, that's not LC engine :eek: It is too clean. Must be an old chevy vega ;p Looks like aluminum. Great job!! I am jealous already :grinpimp:
 
Degnol said:
Thanks all. I'll use that centered hole right below the carb.

Ed

We got the head on, valve train, so its pretty much done. I'm going to have the valvecover beadblasted then PC clear....just for a little 'bling'.


Ed

Woah! I have Cruiser wood!

I agree, do not paint it black. The shop that rebuilt mine painted it black - wish I had gone for battleship gray...
 
Degnol said:
The head and block were "steelabraded", came out looking like new castings. I wondered what to paint it and the consensus was "don't paint it black, because you can't see any leaks" so I painted it Plastikote Cast Iron Gray. Takes 600* and is resistant to most fluids. We'll see, but of course I WON'T HAVE ANY LEAKS...hehehe. I painted all the tin with Rustoleum Satin Black.
Bored .030 over, new pistons and rings, new cam and lifters, polished the crank, new Toyo bearings and gaskets.
I'm "shakin' like a queer at a hotdog stand."


Ed

I have no trouble seeing the water jacket leaks from the crack on my black block. Been watching for 8 months now :rolleyes: .

Your engine is a work of art to my eyes, really, too clean to use, Ed! :beer:
 
Thanks for all the compliments. I learned a lot in the process and was fortunate enough to have a good friend who is a bonafide mechanic to keep me from screwing things up...hopefully. I spent a lot of time smelling like parts cleaner and at the bench grinder with a wire wheel.
I'm thinking about just wheeling the thing into the livingroom and not running it.
The color of the motor is really much better in real life, the flash on the camera makes it look like shiney aluminum, but it is that "just out of the foundry" look.
I'm currently working on getting a 4 speed T/TC to swap in at the same time.


Ya just don't know where to stop.



Ed

BTW, IDave, I'll have a decent running F and a half...that has no crack in the block.
 
Degnol said:
BTW, IDave, I'll have a decent running F and a half...that has no crack in the block.

That's a definite thought. D'ya suppose your wife could drop it off at the post office for me?
 
It used to be said of Ronald Regan that if you were drowning 20 feet from shore, he would throw you an 11 foot rope and remind you that he was meeting you more than half way.
I occaisionally go to Wyoming.

Ed
 
I could go there occasionally, too!
 
Back
Top Bottom