Replacement floorboards - group interest? (2 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Sorry guys, I have been out of town a lot on business (I am typing from a hotel room in Houston right now). The paper mache thing didn't work. NOT a good plan at all. I still have the paper template and with all the measurements posted here by scorcher, we should be in good shape. I'll try to get it in the mail when I get home.
 
k9crazy said:
Sorry guys, I have been out of town a lot on business (I am typing from a hotel room in Houston right now). The paper mache thing didn't work. NOT a good plan at all. I still have the paper template and with all the measurements posted here by scorcher, we should be in good shape. I'll try to get it in the mail when I get home.
Click to expand...
I will get work started on it the day I get the template. Anyone else working on it?
Ehsan
 
I think I'll cast the front floorboards for you. As much as I can. I wish someone out there had a 55 that was to damaged to use but had good whole section of the front floorboards to use. This would make things a lot easier. I'll do what I can. It may take me a while though.
 
Trollhole said:
I think I'll cast the front floorboards for you. As much as I can. I wish someone out there had a 55 that was to damaged to use but had good whole section of the front floorboards to use. This would make things a lot easier. I'll do what I can. It may take me a while though.
Click to expand...
Will wait.. :).
Ehsan
 
I am very needy of the front and rear floorboards; what can I do to help?

Lou
 
Trollhole said:
Eshan are there no 55's around you. I'd donate 100 dollars to the cause. It's going to cost me more than that to send you all this stuff.
Click to expand...
I may be able to find a 55 here. But that would cost me nearly US$7000 for a broken down rig. I am not sure if there is enough demand for parts to go and do that investments.. Comments?
Ehsan
 
Marshal; what about the pig in ATL's floor boards: that might be a good one........are you up for it?

Lou
 
Lou and I got a good look at a potential 55 donor that we could probably hack up and send to eshan. It had everything we all have been wanting. rear corners, rear quarters, and especially the floorboards the rears were in good shape. He is parting the pig out after everyone has gone through it maybe we could get him to sell us these parts somewhat cheap so we could get them reproduced so everyone could enjoy. Only problem I saw with this deal was that it is a 78 model which is different from what I need. But the outer sheetmetal should all be the same. And best of all it had rear corners. They had lots of bondo but I'm sure they would make a perfect partern for Eshan to make parts from.
 
Trollhole said:
Lou and I got a good look at a potential 55 donor that we could probably hack up and send to eshan. It had everything we all have been wanting. rear corners, rear quarters, and especially the floorboards the rears were in good shape. He is parting the pig out after everyone has gone through it maybe we could get him to sell us these parts somewhat cheap so we could get them reproduced so everyone could enjoy. Only problem I saw with this deal was that it is a 78 model which is different from what I need. But the outer sheetmetal should all be the same. And best of all it had rear corners. They had lots of bondo but I'm sure they would make a perfect partern for Eshan to make parts from.
Click to expand...
Sounds good. Any pics?
Ehsan
 
will try to take some pix next weekend or two; mayb eask k9crazy who lives close by to take them as I live about 4 hours away from the one Mashall is talking about;

Lou
 
Hi Eshan,

Newbie here, been reading this thread and am pinching myself to see if I'm dreaming!!!

I noticed most of the panels the Aussies make are flat or 2-D, even their rear corners are not "wrapped".

"Would your designs be like this as well, or can you make the rear corners 3-D?"

Got a feeling you would sell a ton (literally) of those panels here. Are you seeking an international distributor or keeping it private label? If you are selling them yourself, then this newbie would be honored to be in line for your panels. (I miss my corners... ...so does my Piggy).

Best Regards,
George
 
GreasedPiggy said:
Hi Eshan,

Newbie here, been reading this thread and am pinching myself to see if I'm dreaming!!!

I noticed most of the panels the Aussies make are flat or 2-D, even their rear corners are not "wrapped".

"Would your designs be like this as well, or can you make the rear corners 3-D?"

Got a feeling you would sell a ton (literally) of those panels here. Are you seeking an international distributor or keeping it private label? If you are selling them yourself, then this newbie would be honored to be in line for your panels. (I miss my corners... ...so does my Piggy).

Best Regards,
George
Click to expand...
Hello there
I dont have a distributor in the US and I send stuff direct to the customers.
Good News...
The first sample repair panel for the fenders is complete and you will see pictures in a few more hours time. These will include the rolled edge in front also.
What exactly do you mean by 3D? Please specify or post a picture/link. I plan to make the rear corner panels that would wrap around the corner. This will be very difficult but we will try at our end. If not then we will make the straight pieces.
Ehsan
 
Here is an 'Incomplete' panel that we are working on. We will have 9 sets ready by Monday.
Ehsan
photo3.webp
photo2.webp
 
:cheers: OMG, fresh Piggy steel!!! :cheers:

Hi Eshan,

Regarding the 3D curve, it is exactly the area you mentioned. The lower, rear-most corner of the vehicle. This is the point where the side meets the rear valence (2D), then they are both rolled under (thus, 3D).

This corner ends up looking like a "ball" for lack of a better term.

(I wished I could post pics, but my status is not up yet:o )

Keep up the great work!!!

Best Regards,
George
 
You must log in or register to reply here.

Similar threads

jestlurnin
Windshield wiper blade replacement
Replies
2
Views
788
bobm
B

Users who are viewing this thread

Total: 3 (members: 0, guests: 3)

Share this page

Back
Top Bottom