purchasing an aussie locker?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 27, 2003
Threads
490
Messages
9,929
Location
North Cadillac
I was looking around at the mud vendors, slee, IPOR, ect.. and no one carries the aussie locker? Do you have to order direct from them on the other side of the pond?
 
Interested to see where you get yours from, I'm thinking about picking one up soon for the rear of the 80. I wonder if there would be any chance of getting better pricing if we picked up a few at a time?
 
Got mine from their website...dont think there is anywhere else.
 
steve, i'm pretty close to pulling the trigger. I was thinking we could get a few purchases together and maybe catch a break on shipping or knock a few dollars off. We can put yours in and learn from our mistakes before we put mine in!! :)
 
i got mine from offroadlockers, shipping was $23.00 the install wiki (https://forum.ih8mud.com/80-series-tech/118690-aussie-locker-install.html) is very good, the instructions included are a little generic and jump around some as they cover installation on several different axle models. make sure you have a new axle gaskets ready (2 axle shaft/1 3rd member). the local toyota shop had to order mine took an extra day to get back togeather. i love mine :p
 
ok, so 2 axle shaft and 1 - 3rd member gaskets are needed; do you use any type of rtv sealant as well, or just the gaskets? Are you guys ordering any of the different thickness washers from Toyota before you tear into the install? Anything else needed besides gear oil? I would hope to do the install in one day, ie only have my rig down for a day if at all possible.
 
Fourtrax, that install you linked to by Hayes is a great write-up. After looking at it, i'm actually contemplating an install myself which before hand i was really scared to do it.

I'm not going to order any shims yet, as i have another vehicle to drive and i'm not in a hurry to get it back together. Plus, in the write-up it appears that the majority are fine on clearances and new shims are not needed, most of the time.

I still have not pulled the trigger yet, just doing a little leg work.

Also, offroadlockers is just torquemaster's web page or aussie locker's web page; so again, it looks like you have to order direct from them on the other side of the pond.
 
I didn't use any sealant, just the gaskets.

I have put about 1k miles on it and no issues so far. if you have never had a locked rear you will want to play around once you get it installed your vehicle will react different especially when off camber and down hills. just understand want to expect and you will be fine.
I actually pulled the 3rd out using a jack to balance it (it is heavy). But, I didn't have any issues. My 10 year old daughter actually did most of the aussie install of course I double/triple checked the clearances, and even with 241K mile I was still within the aussie specs, so no shims needed. If I had the gaskets in hand it would have taken about 3 1/2 hours from start to finish and that was with explaining everything to Hannah and a couple breaks along the way. The cone washers were the hardest part.. (just use the hammer authoritatively). Keep track of which side the shims came from and remember to support the axle shaft when removing them to replace the gaskets, so the teeth on the end of the spline don't touch (cut) the seals. And don't forget the 3+ quarts of your favorite diff oil. It's easy....
 
Last edited:
The write up by Hayes is very good, no reason to not do it yourself IMO. There are way harder maintenance items we do to these 80's. I only wish there were as easy of a solution to lock the front. I should be ordering mine very soon.
 
Put mine in just before Cruise Moab with the help of a friend. I ordered shims but don't think I used them. Probably 2K miles on it now with no issues. Worked perfectly during Cruise Moab and has been great on the road. I was worried since the truck is driven by my wife every day but she doesn't notice it other than the faint ratcheting noise. We'll see how it goes this winter. that's the only question at this point.

I ordered it from their site as well.
 
steve, i'm pretty close to pulling the trigger. I was thinking we could get a few purchases together and maybe catch a break on shipping or knock a few dollars off. We can put yours in and learn from our mistakes before we put mine in!! :)

Sounds good on doubling up on the order, just let me know when. I figured we would install mine first, then right after we were done with mine I was planning on pretending something came up and then jetting on you :flipoff2:
 
hi

ordered mine from the website.just put it in on 1991 ,didnt need any new shims.took about 3 hrs.i cant even tell its in there on the road.:beer:
 
alright steve. Let's see if any of the NC/SC crew would be interested in a group buy. I can't wait to do some serious doughnuts if we actually get snow this year!!
 
If you don't mind me asking, how much is the Aussie Locker?:D If it is cheaper than an OEM retro locker, I may be interested on a group buy:cool:.
 
Back
Top Bottom