Power steering?? fj 45

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Probably the most covered topic on MUD. Just do a search on power steering. There are complete kits available from several vendors or you can create your own. Good Luck!
 
X2 on staying away from the mini truck. Not only rub on big tires, you end up keeping the weak link center arm

nocents
 
If you want to stay Toyota?? FJ60 gear box is the way......
 
Hi All:

I installed a GM Saginaw PS conversion on my FJ40 a few years ago with the help of a fellow 'Cruiserhead. It works great for me.

That said, I don't think there is anything wrong with the so-called "mini-truck" PS swap, as long as the rig is stock or just mildly modified. The "mini-truck" PS swap is very similar to the Toyota OE PS sytem used on very late production 40/45 Series TLCs.

For big tires and 'lockers though, one needs a PS sytem that can provide more power; the GM Saginaw or Scout Saginaw work well here. I don't know much about use of the 60 Series PS gearbox on a 40/45 Series.

Regards,

Alan
 
FWIW,

I run the mini truck steering on my fj40 with 35's, and have driven a lot of rocks here in Colorado, and run trails in Moab rated at 4. No issues, I like to stay Toyota.

It is an excellent addition to any cruiser. And with the mini-conversion, you will have only a few hours of down time and no fabrication to deal with, which was a must as mine is also my only DD.

Just my .02

Rezarf <><
 
There is a guy redoing his 40 here (Mountaincruiser) he is doing a great job and has a good thread. He had already powder coated his frame and had not yet made a decision on PS. Here is the discussion that followed and some links for the 40. I think he decided to go Mini because there would be little damage to his powdercoating.

"I am going with Saginaw on my project because larger tires will rub on the Toyota Mini setup but then I have not done all the work to my frame yet. The Sag requires a good bit of welding to the frame horns and to the MAF SR you are running. This means fawking up your powder coating.

The mini truck stuff is basically bolt on and there is a great "how to" someplace in the FAQ - step by step with pics and it took the guy a long day. It is considerably cheaper then the sag set up once you figure in the welding and brackets and u joints, etc for the Sag.

The Sag is argued to be the tougher of the two set ups and more readily available due to the number of US cars in junk yard that ran a Sag box over the years.

Personal decision you have to make now. I would go mini truck at your stage and reduce tire size/width because the frame is already coated. Otherwise I would do a Sag AND THEN coat the frame.
Here are some helpful links. It took me a long time to figure out what I was going to do and understand the various ways to do it.

http://www.off-road.com/tlc/tech/saginaw/

Good brackets: http://www.deckersonline.com/

How to mount them: http://www.off-road.com/tlc/tech/psbracket/

This is the good Mini truck install from the FAQ I mentioned: https://forum.ih8mud.com/showthread.php?t=65318&highlight=mini

This has all bee discussed here ALOT - don't opent he can of worms - LOL There are alot of views - I hope mine helps. I have a whole bunch of other links I bookmarked on my comp. PM me if you want me to send them to you. They are vendors for U Joints/pillow blocks/ steering shafts and some other install ideas for Sag."
 
At what size tire with factory back spacing does rubbing start with the mini set up?
I have heard anything over 33 12.5 but I could be wrong.:doh:
 
oh horse pucky! mini truck is 90% the same as OEM fj40 PS and it works GREAT with up to 33" tires. It all DEPENDS on what your goal for the PS is, for some mini or OEM is the way to go, others Fj60 or Scout, others yet.........GM/Sag and others still ram........it just depends. a statement like yours needs to be backed up with some real info.....

also..........stay away from DUI ignitions :D

what ever you do stay away from the mini set up!
 
I have heard anything over 33 12.5 but I could be wrong.:doh:

35x12.5x15 MTRs factory backspacing... no rub.

Rezarf <><

I am not saying that mini-truck is the only way to go, not at all, but the mini-truck is much better than some give it credit for.

To each his own I guess.
 
Hi All:

I think the most important part of this question is "with factory backspacing." Many of us here in North America run aftermarket Chevy/GM wheels because they are cheap to purchase and share the same bolt pattern as the Toyota solid axle trucks. But, they have a backspacing (3.75 or 4.0 inch) that is deeper than the stock Toyota rims (3.5 inch) which combined with tires much wider than the factory engineers ever imagined can lead to rubbing on the body sheetmetal during suspension movement.

Regarding tires rubbing on the "mini-truck" PS system, I have not heard of this being a major issue; it cannot be any worse than whatever rubbing might be present on the stock manual steering with wide tires.

Regards,

Alan

-----------------------------------------------------------------------------
"Conex" asked:

>At what size tire with factory back spacing does rubbing start with the mini set >up?
 
Back
Top Bottom