Normal street manners for lock-rite?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 23, 2002
Threads
46
Messages
463
Location
North Bend, WA
I recently installed a (used) lock-right into my 71 FJ40. After the install, I noticed the rear eng would "push" out to one side when I accelerate, and pull back when I coast. Felt like the spring bushings were shot. Bought new bushings. Old ones didn't look bad.

It was doing it so bad this weekend, I had to stop an check that the springs weren't busted, frame wasn't broke, etc. I find nothing physicly wrong.

Do lock-rights act like this? I installed per the directions (including the measurements) I got a auburn LSD and may put that in the rear instead.

Would the lock-rite work OK in the front? I do have pwr steering.
 
mine clunks around. actually, I was driving my rig today and I when turning to the right, the clicking is more prominant than to the left. I guess turning to the right (going about 30ish) sounds like a full 'click', going to the left sounds like about a half click. Also, sometimes there is a really 'loud bang' and it sounds like I broke an axle or something... this only happens from only once in a while and ive heard others reporting the same with this style of locker.

I think the feeling you're getting is more of the feel of the rear end. you're going to feel more than with no locker. someone made that comment at one point and it stuck with me for some reason. From what ive read, this is normal...

hth, mike
 
It is pretty normal operation for all auto lockers. Easing on and off the throttle will make it less noticible, you you will still feel it especially between shifts. After a week or two of driving it you won't notice anymore.
 
It's been in there about 2 months. The clicking I can deal with. The street manners are another thing. I have an auto, so there is no shift movement.
I thought something major was wrong (might still be, but I haven't had time to check it yet
 
Mine does exactly the same. It makes onlookers think you are either a crappy driver, or you just broke something. Hearing the loud SNAP! reminds me that it is still working though. To date the Lockrit has snapped 2 axel shafts for it's previous owner in another rig, and a pinion in my rig. Therefore I concider it a pretty good BANG for the buck (pun fully intended)!
 
Would the lock-rite work OK in the front? I do have pwr steering.

Don't put the auto locker in the front. Auto lockers only belong in the rear. If you want lockers front and rear get ARB.

You need to drive a little differently with an auto locker in back. I always try to clutch through turns. You'll hear the locker ratchet, but it won't pull like you describe. This is mainly at lower speeds. Mine handles fine at higher speeds and is not noticable.
 
Would the lock-rite work OK in the front? I do have pwr steering.


I have run an ez-locker in my front end for about 2 years.

It works fine, I just engage and disengage the front output when running around trails between obstacles. The only truly annoying time is when driving downhill and 4wd is needed for engine braking. I have FJ60 P/s and it is still very difficult to turn in this situation. I'm installing hydro assist for that reason.
 
It's been in there about 2 months. The clicking I can deal with. The street manners are another thing. I have an auto, so there is no shift movement.
I thought something major was wrong (might still be, but I haven't had time to check it yet

Both my Aussie lockers act just like your LockRite. (rear of FJ40, rear of 4runner) I get lots of rear end sway when getting on and off the throttle. And it is much more prominent while turning.

My intuition is that it has to do with the way torque is applied to each axle. I believe the axles in open or LSD diffs get torqued with slightly different timing as a reaction to engine and body torque. Locked axles must respond at the same time. This is vague and I'm sure 25 guys are going to call bull**** because I can't offer proof. But some day someone smarter than me is going to bear me out. I know they will, I just know it.:)

You're on the right track with replacing bushings and checking for play at the "joints". Seems like flexy and lifted might compound the effect also.
 
yes its normal, buggy but youll learn to live to deal with it. ease into and off of the throttle
 
I wish the OEM locker in my 71 Chevy pickup was being made for other applications. Despite being a Detroit, it's the most forgiving, easy to live with locker I've ever had. In fact, I didn't realize there was a locker in there and bought a used one to install. I went around a tight corner one day (hairpin) and got on it. The rear end suddenly jumped over and I knew then it had a locker. No bang, though. It's never done that, nor has it displayed ill manners unless I romp on the gas.

(For the curious, this locker is on an Eaton axle, which is stronger than a 14-bolt. If you wanted a locker, you got the Eaton, which looks like a Ford 9" on steroids, that is, it's a Hotchkiss design. The brakes and hubs are the same as a 14-bolt. The Eaton is very heavy duty, but Lord help you if you need to replace parts - bearings, for example, are very expensive.)
 
Back
Top Bottom