New and head trouble

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 17, 2017
Threads
1
Messages
19
Location
Minnesota
Hello gentleman. Long time in the weeds first time out in the open. I have had a 6/75 40 for about 10 years went from driver to "lets restore it!" to it is to far gone. (Minnesota winters before i had it) Looked for years for a parts truck as i could not let the 40 go. recently acquired a 12/75 with a great survivor body that has now become the primary project. I will post picks. The previous owner drove as daily until the engine "blew up". which brings me here. I have no compression in hole 6 and the exhaust valve is sitting about 1/4" above the rest and could not be adjusted. Also this engine is painted Fo*d blue. Rebuilt? See Pic. I am very mechanical but have never gone in this deep. I am sure I will have to pull the head. Any other hope of quick fix? Great to be here will contribute when and where i can. Thanks
20170707_152621[1].webp
20170718_213044[1].webp
 
Welcome.


Interesting head bolts...


There is not any kind of a "quick fix" if you have a broken valve...


It may be cheaper for you to find a good used engine, in the event you find that one is garbage...
 
Put your air compressor to it, listen for a leak at that valve. Either way that head sounds like it is coming off soon. Good luck.
 
Thanks for the advise. i figured it was coming off just did not want to miss somethings stupid. I have a parts truck with running engine. I will pull head on this just to look but sounds like i would be better off investing time $$ in other engine. Thanks.

There is rumor that it is an 85 FJ60 engine. checking.
 
Removing the head and working on the engine isn't very difficult - and you'll learn cool things while doing it. Go for it - pull the head and inspect the valve train and the bore and find out what shape it's all in.
 
Boss at work popped the head off a valve in his off shore boats one cat engine.
That completely destroyed the block and head.
 
Pulling head tonight. when turned by hand and during compression test there were no strange sounds. Will post up some pictures when i get it apart.
 
Pull the head. Bring to machine shop. 300 or less they will clean it and rebuid it. While it's off re ring the pistons. New head gasket of course. You'll be good to go.
 
Well it is apart. Those are valves in the bottom of the intake. Looks like the sixth cylinder lost one of the its valves then broke the other one. pcs where drawn into intake and then into cylinder 1 leaving the big parts behind. Looks like the head is junk? Also is this intake junk. there is a crack at the bottom. Most of it is behind the valve pcs. I have a tired but operational 2F out of another 40. (body is gone, decent running gear) I think put the money into that. Recommendations?
20170719_190407[1].webp
Bottom of head
20170719_194916[1].webp

Top of piston at 6. I rotated piston down and did not see and scoring. the bore seems smooth. Only damage is at back right at the top. You can see it in the picture. Had to have made a heck of a noise.
20170719_194546.webp

Pcs in cylinder 1
20170719_194538.webp


Is it normal to have different sizes on cam end of push rods. they are in order with the left being #1
20170719_194941.webp

Well any kind words, condolences or moments of silence are all welcome. I am going to bring head in and see what they can do.
 
Last edited:
yikes.... go with poser's suggestion. find a new engine.
if youre going to rebuild may as well have a usable block and head and one that hasn't undergone catastrophic
engine failure.
whats up with two different sized pushrods?
 
yikes.... go with poser's suggestion. find a new engine.
if youre going to rebuild may as well have a usable block and head and one that hasn't undergone catastrophic
engine failure.
whats up with two different sized pushrods?
The pushrods came out that way. Seemed strange to me. they are in order.
 
Time to Borrow a 2F from the 40 next door. blue 2F is the one i have apart. one in back ran when i parked it.
20170707_152621[2].webp
 
Because someone put together a collection of parts to make something work...That is why you have miss-matched head bolts and push rods...


Head is junk.

Intake is junk...I mean, you might be able to TIG it, but, I would not mess with it.

:beer:
 
I wouldn't waste time with the block either.
 
Thank you everyone. I will scrape the engine. I am going to pull fuel pump and alt and other for back up parts. Any value in any of the parts or just haul it all to the scrapper?
 
Got it. Thanks. I was going to hang on to t-case and trans. Any way to tell that they are original, or close to? The body on this truck is super nice. i can not believe that it has a different engine and that the guy that built it did a terrible job. Makes me concerned about what else the guy touched on this truck. Nothing that cant be repaired or replace i guess. I am going to start rebuild of the other 2F i have. I will put in new post. I am also planning on using the tcase and trans from that as it is a much more honest drive train. Burns a little oil, some oil leaks, 125K and original to the 6/75 40. Again thanks to all.
 
Back
Top Bottom