Help. Calling all RHD 75 series

[coldtaco]

So, doing the sound proofing of the floor I accidentally covered up the bolt hole for the right side seat belt bolt. No easy way to locate it without removing the fuel tank, which I don’t want to do, at least not yet. Can someone with a RHD 75 make a drawing with dimensions of where this hole is? Appreciate it. In the picture where the silver pen is pointing at is the seat belt bolt hole for the left seat (bench seat) on a RHD 75 series.

 

[Squash]

Ouch!
If I can remember this.
Will look for bench seat hole though mine is currently a two bucket setup.

 

[coldtaco]

I need the location of the drivers floor seatbelt anchor point. I have the one for the bench seat

 

[Gun Runner 5]

I need the location of the drivers floor seatbelt anchor point. I have the one for the bench seat

I assume that anchor point would be different for a 75 Series vs a 79 Series cab?

 

[WarDamnEagle]

Well in my LHD 75 series they are bolted to the same hole (as in stacked). It will be hard to find something that might not be there.

 

[coldtaco]

I assume that anchor point would be different for a 75 Series vs a 79 Series cab?

Probably, especially with a wide nose cab

 

[coldtaco]

Well in my LHD 75 series they are bolted to the same hole (as in stacked). It will be hard to find something that might not be there.

It was there but I accidentally covered it with the sound proofing

 

[WarDamnEagle]

It was there but I accidentally covered it with the sound proofing

I have the 3 passenger front seats (split bench) so my two seats are only 2" or so apart. You must have bucket seats in front?

 

[coldtaco]

I have the 3 passenger front seats (split bench) so my two seats are only 2" or so apart. You must have bucket seats in front?

I had a RHD bucket/bench set up on my RHD HJ75. I switched to two bucket seats.

 

[coldtaco]

Looking through pictures I found this picture and circled the hole/nut I covered over. I guess I will need to keep fishing for that hole, when I get back from work.
Thanks for trying to help.

 

[Squash]

You could fish with a needle....

 

[sodafeld1]

x2 fishing with a needle tool, at least you know it is there

 

[tmarx]

I will be with my vehicle on Sunday only and will then strip out my front seat and measure for ya ?

Here is the post when I changed my seats with some pics to give you a vague idea where to "fish" ...

My "new" sickness .. aka Max. - https://forum.ih8mud.com/threads/my-new-sickness-aka-max.908875/post-11589572

 

[sodafeld1]

Don't say I don't love hj75's, appeciate Taco or Mud!
95mm to the left 120mm to the back center of left back bolt hole of handbrake. Sorted. (had some more pressing issues for a tad)

 

[sodafeld1]

whoops, wrong hole, been told that before! 20mm left then 160mm back from right rear handbrake hole.

 

[Felde]

In my BJ73 all these holes penetrate through the floor panel. When stuff is bolted in, you can see the bolts from below.
You may be able to find the holes from under the truck and stick a needle through?

 

[coldtaco]

In my BJ73 all these holes penetrate through the floor panel. When stuff is bolted in, you can see the bolts from below.
You may be able to find the holes from under the truck and stick a needle through?

Not so easy on a Ute or troopy as the main fuel tank sits there.

 

[Felde]

Autsch. I better shut up

 

[2fpower]

Do you think my LHD 73 would be the same?

 

[coldtaco]

I don’t know. Seems like some of these holes/captive nuts would be different between lhd/rhd and weather or not you have two bucket seats vs bucket/bench. I know I had to find one of the captive nuts for the left seat inner seat rail, remove the skin over this captive nut.