Greasable shackles/pins

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 1, 2004
Threads
107
Messages
474
Location
Phoenix, AZ
Since I'm doing a spring lift soon, I was wondering...

if its worth the time and expense to replace my leaf spring shackles or shackle pins and hangee pins with greasable ones? If so does anyone have recommendations? These need to fit a 1962 FJ40.
 
Use regular bolts, they are not hollow, soooo they are stronger. Then find some 80 year old wagon wheel grease (thick, almost like bees wax) to lubricate the bolts/bushings. The heavy grease remains inside, does not pour out of the bushings like water as modern greases do, then doesn't let dirt/sand/mud/water enter- - -easy deal.
 
Use regular bolts, they are not hollow, soooo they are stronger. Then find some 80 year old wagon wheel grease (thick, almost like bees wax) to lubricate the bolts/bushings. The heavy grease remains inside, does not pour out of the bushings like water as modern greases do, then doesn't let dirt/sand/mud/water enter- - -easy deal.
FYI, putting a hole in a shaft will actually make it stronger not weaker because you have added an additional surface. IMO go with the 5/8 grease-able pins from SOR, especially if you are crossing water in your travels. A tube is stronger than a bar of material, a physical fact. I would ditch the stock shackles unless your into a unmolested and unmodified stock must be original rig. The vendor is only a suggestion, lots of choices there.
 
Thanks guys. Will stick with the stock hardware.

If you are going to wheel it, you are missing out on endless entertainment!:hillbilly:
attachment.php

attachment.php
 
Looks like that one came apart and then snapped in two while hanging out of the spring, dought if the hole had anything to do with that failure.
 
A few months ago I replaced my rear springs. On the shackle end with my homemade shackles and greasable pins, the pins (5/8 drilled bolts) slid right out by hand after being in there for about a decade and they looked perfect. I re-used them with new poly bushings The other ends with stock pins were a fight getting out. I replaced those with the store bought greasable pins and have greasable pins all around now. New front springs are laying in the shop waiting for me to put them in. I use the moly grease that I use in my knuckles since It's easy to find and I grease often as I'm always wheeling in deep water. Lots of limestone wheel size holes hidden under that water and I'm always pounding the crap out of my rig while often over loaded. Haven't broken or bent any pins yet but if I do I'll post it. I'm sold on greasable pins.

My homemade pins in this thread
 
Looks like that one came apart and then snapped in two while hanging out of the spring, dought if the hole had anything to do with that failure.

The nut on the other end is still in place, it broke at the cross drill, the same as all of the others we have seen.
 
The cross drill is the issue not the bore drill
 
Then I guess everything I learned about the strength of "mass" is all

Lol that is a very non quantified statement so I am just going to say if ur were of the belief that strength related to mass then yeah ur are all screwed up :)
 
Last edited:
Lol that is a very non quantified statement so I am just going to say if ur were of the belief that strength related to mass then yeah ur are all screwed up :)
You are probably right about me being all screwed up, but I doubt my Heat Treaters, Metallurgist, and Stress Analyst Engineers are.
 
You are probably right about me being all screwed up, but I doubt my Heat Treaters, Metallurgist, and Stress Analyst Engineers are.

There is no way that any engineer told you that strength was related directly to mass . If that was the case then everything strong would be very heavy and the aviation and space industries would never get off the ground. It is a consideration in some applications but you are out of context in your usage. Give your engineer buddy a call and ask him / her straight up :)
 
Wow! People dissing Jim! That's a first. Be careful, he's got more smarts in his avatar than most people do in their keyboard commando life.

I am not dissing anyone I am just pointing out that if he believed mass and strength are directly related without context and variables then he is well off bass with his assumption. I am well aware who Jim is and what he use to do but that has no bearing on his statement about the above and if it is accurate of not.

All that being said since others are getting the impression that I am dissing someone who has been an active and contributing member of the community longer than I have probably been alive I will leave the topic and if anyone wants to know all about strength they can simple google it and do some reading
 
YoYoHo is correct that this is a "context" issue, mass is usually substituted/replaced with material quality, heat treat, etc., but with that said, I doubt the hollow spring shackle pins have any exotic materials or heat treats???
 
Last edited:
Adding my $.02

Having two rods of “equal mass”, hollow will be stronger than solid. That’s because the hollow one of “equal mass” will have to have a larger outer diameter to be of “equal mass”.

Now two rods of “equal diameter” where one is hollow and the other solid, that’s another story. Drilling a hole in a bolt and making it stronger?? I don’t think so.
 
Back
Top Bottom