Forensics via photos

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 20, 2007
Threads
200
Messages
9,414
Location
Auburn
Apologies but this thread is sort of a continuation of one from yesterday. I have found a 40th 80 with Lockers. It's in the south now but it has spent most of its life in Ohio and Indiana. Looks like probably the first 130k and it has 144k on the odometer now. Obviously rust is a potential issue. I'm aware that it might need other maintenance issues (e.g. axle rebuild) but none of that would scare me off as much as a rust issue as I would plan on keeping this for a very long time (and it will be residing in the southeast going forward).

If you only had these photos, what would your evaluation be in regard to the rust?

Thanks!
97 TLC 002.webp
97 TLC 003.webp
97 TLC 006.webp
 
From just a limited selection of photos it's hard to say. My truck has been a midwest truck all it's life and has 10x more rust than that on the undercarriage.
 
If you only had these photos, what would your evaluation be in regard to the rust? Thanks!

The 40th Ann truck I wrecked in 2005 came from Maryland and it had rust on it. I bought it because of the impeccable one-owner, garaged service history (and low mileage), but still worked my a$$ off cleaning it up. New calipers, rotors, e-brake assemblies, cables, bolts, nuts, exhaust, blah blah blah. Never again. The money I blew cleaning it up would have paid for a rust-free truck to be hauled in from somewhere else.
 
Running gear looks rusted (typical, not excessive), but the engine looks steamed and somewhat free of pitting from salt. I would think if the body was equally free, it was washed in the salty months. I would ask for pics of each wheel well, the rocker panels, and the bottoms of each door, as well as the rear hatch inside and out.

If they are rust free you know the only problems you will have will be underneath. Buy stock in PB Blaster if you buy it. Everything under there will be a pain to work on.
 
I'd say don't buy without either checking it out first hand or obtaining more conclusive photos. 40th Ann wouldn't mean much if it's a rusty pita to work on.
 
Thanks for the comments everyone. I should probably just be patient and wait for the "right" one. Price (within reason of course) isn't so much a criteria as is condition.

Found this one on ebay:

http://cgi.ebay.com/ebaymotors/FL-4...oryZ6443QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

It's relisted as it failed to meet reserve at a high bid of $7802 a couple of days ago. I thought about it but thought that I would eventually find one with lowish miles (+/-100k). I did run a carfax on it and it checks out as a one owner, Florida only vehicle......but the miles...

I've only been looking a few weeks and I don't really need it until next summer so I'll probably pass on both.

Again, thanks for the comments. :)
 
doesn't rust typically become first an issue getting through the light sheet metal over damaging heavy steel frame members?
 
e...true, but that rust underneath makes it a pain to work on...everything is compounded by rusty bolts, etc.

If (IIIIIFF) the PO washed it regularly in the salty times it can have no rust in the sheet and still show what we see below.
 
yes, it's all a matter of perspective. Light *Surface* rust on the drivetrain would not bother me one bit on purchase. That's just cosmetic. Now if it gets more seriously in the metal with hard to remove rusty bolts etc that's another story. Anyway, my point again is that I would also look carefully at rocker panels, fenders, window frames etc besides just the frame and axles...
 
I did see that a few weeks ago. No lockers. Thanks for the lead anyway.


you can always add ARB's to the picture. I'd pass on a semi rusted locked over a clean unlocked anyday. Especially if you are going to be running 35+ and pushing it hard. While factory lockers are sweet, a lot of them haven't been used and could be seized up, rusted up (especially if the undercarriage is bad, that rear locker can easily seize.) If the actuator is messed up, you either have to buy used, (rebuild is possible) or buy new...and new is $$$

I would go for the cleanest well kept rig(documented) and go from there.
 
my truck has been in the North east it's whole life and the axle's rust the worse on the truck. I suspect that if I keep this truck another 10 years I'll have to do something about it. Any time pics of a truck from the North are posted up a bunch of people from the mid west will post horrifying comments about it. They just don't have a good perspective on it. Elmariachi's post is a good example of this. He bought a truck and then went crazy on replacing parts that were no where near their end of life because it had rust on it.

If you look around you will find plenty of 40s, 55s, 60s and 62s that are rusted to the point of being worthless. I've yet to see that with an 80. Is working on a 10 year old vehicle from the mid west easier, absolutely. But if your budget demands that you need to save a little at the expense of dealing with a stubborn bolt then don't let these guys convince you the truck worthless.

So far most truck's end of life comes from an accident or roll over. Being rust free doesn't effect those odds at all.
 
I think Landtank has a good perspective on this. My truck spent its first six-seven years in NY and had about the same amount of rust on crossmembers that you show in the photo. It had a really clean engine compartment and no rust on any sheet metal- just on some of the heavy steel underneath.


I pressure washed it off the vehicle and treated it with a POR-15 type spray. The only part that needed work on it (mechanically) was the emergency brake mechanism which I had to replace one part on to get it working (inexpensive).

I've now had the vehicle for over three years (in the South now) and never had any problems with rust/corrosion returning.

I still recommmend seeing it in person which makes Ebay type purchases a bit risky, and dont recommend purposely buying a rusty 80, but do think they are pretty well treated against corrosion at the factory and I wouldnt get too worked up about it.:popcorn:
 
Back
Top Bottom