FJZ80 Aussie Locker - Rear

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 27, 2008
Threads
5
Messages
38
Location
Ventura County - So Cal
I am researching locker options. The Aussie Locker seems to be well regarded.

My concern with the Aussie is additional driveline backlash.

I had a Jeep TJ with a Dana 44 and installed the higher end Lock-Right (seems a similar design to the Aussie). It worked well but added a lot of backlash to the driveline. It was very noticable during on/off throttle manuvers.

Does the Aussie Locker installed in a full floating FJ rear add similar backlash and the associated driveline wind-up?

:cool:
 
Other than some clicking in low speed parking lot maneuvers, I can't tell mine is there. It's been installed around 3 years.

No wind up or backlash. The only time it "banged" outside of new install, was when I took a corner real hard and gassed it on pavement.
 
Mr. Gee, if you install an aussie in the rear and find that you hate it, I'll buy it from you...
 
I'd take the Aussie over a lockright. I've had an Aussie in my rear semifloat for about 9 months. No issues at all. Can't tell it's there on the road except for the ratcheting sound during tight slow corners. Works great on the trails. Been very happy with it.
 
I don't think the lock-right is "higher end" just b/c it is more expensive. X5 on no problems.

Lock Right had 2 versions, the $200 dollar one and the $300 dollar one. I meant the $300 dollar one was the higher end of the two.
 
Aussie Locker

Based on all the recommendations here I am going to go with the Aussie

Thanks all.......

:cool:
 
I love mine! I don't even know it's back there except the slight ratcheting sound during real tight turns as described above.

You can "almost" make it selectable using your CDL button and Pin 7 mod. With the CDL unlocked, the rear aussie will not fully lock around turns, so no binding. Lock the center diff and it will lock up the aussie.
 
You can "almost" make it selectable using your CDL button and Pin 7 mod. With the CDL unlocked, the rear aussie will not fully lock around turns, so no binding. Lock the center diff and it will lock up the aussie.

jigga what?
That unit is all mechincal it has no idea if the transfer case is locked or not, so how does this work? My experience has been the aussie will not release if it's under load sometimes, but that's not even all the time. I'm sure it's physics about it beng bound up so it won't release until the load lightens... but as close as I got to that school course was I once walked by that classroom on the way to Special Ed.
 
yea, with the center diff unlocked it will ratched around turns instead of bind when it's fully locked. If you lock the T-case, it will cause the rear to fully lock and bind in a turn. Give it a try.

I crossed it up in a ditch with the RF and LR tires off the ground in H range and CDL unlocked. Rear tire in the air spun and the tire smashed into the ditch side didn't spin. Locked the CDL and it walked right out.

EDIT: maybe i need to try the cross up test again to see how accurate it is.
 
That was a fluke, you should NEVER have a negative differential in axle shaft speed with an auto locker. Positive is fine, which is what happens in a turn...the outside tire going faster than the inside.

I think yours must have just been getting broken in, cause that doesn't ever happen for me. You sure the rear was spinning?
 
i'm going to do further testing on this because no one seems to beleive me. Maybe it was a fluke, but Jfz80 was in the truck when it happened and he can attest that it was pretty cool.

I think it has to do with the viscous coupler not sending enough power (torque) to the rear to make it lock up.

Testing to come!
 
I don't doubt that it happened, I just know that it shouldn't. Have you duplicated that again, or did this happen only once.

Well, sort of. When we were at URE, when i would run in L with the CDL locked, the tires would scrub in turns. With the rig in H range and the CDL unlocked, it would just ratchet.

I never really crossed it up and tested it. Plan on doing that this weekend.
 
Sorry Mr. G :o
thread_direction.gif
 
Back
Top Bottom