Fj40 Exaust location

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 16, 2004
Threads
46
Messages
289
Location
Southern California
I currently have the Downey Chevota headers dumping the mufflers just underneath both doors, outside frame, on my SBC V8 FJ40. I am now going to use Block hugger headers and route the exaust underneath and inside the frame.
Question: Has anybody tried mounting the dual mufflers up inside between the rear wheel wells. It seems like it would be a good place to keep them out of the way of big rocks, and also out of the water in a stream crossing. The only thing negative i can think of would be the rear floor heating up. If anybody has tried this id like to hearthe pro's and cons
Thanks Jerry
 
I have not done exactly what you describe but close on my 60.

I'm running block huggers. Right side crosses under oil pan and follows left side back into a y pipe. Single 50 series flowmaster. Then dumps straight down perpendicular to the ground about 4" behind rear axle. complete system is above the frame rails except final dump pipe. It its location it would be pretty hard for anything to hit it.

My only complaint is when idling in place you get a little ehaust moving forward as it hits the ground and disperses.
 
I fail to see the benifit of running a dual exhaust system in a 40.


I have ran my muffler in this location for a year without issue...



:beer:




RedAxle-36.jpg
 
technically.. would it not be more tubing, bends, angles to go that route versus just under the doors (which is my setup also - right in front of rear wheels) and thus, a supposed loss of power due to the restricted airflow?
 
I ran duals with the fenderwell heaters...er, headers.....yuck

switched to GM "stockish" manifolds with dual exhaust out the back...no "clean" method of doing the passenger side without a loss of clearance...

switched to block huggers, a custom Y-pipe, and a single 2.5" exhaust...loved it...

switched "yet again" with the same block huggers, a slightly larger y-pipe, and a 3" exhaust...noticable torque loss....

switched FINALLY to center dump ram's horns, the "off the shelf" y-pipe, and a single 2.5" down the DS frame rail, exiting straight out the back just inside where the rear spring hanger outta be....works great, sound is out the back and quiet, and I've only tapped the exhaust at the exit....

and I wheel it hard....

IMO, that's my favorite thus far.....

(is 5 exhaust ideas in ...mmmm....well, since 1989, a bad thing?!?)
 
Hey Thanks for all the info guys! Got some good ideas. I did fail to mention that i have a Con-Fer fuel tank mounted in the rear which makes the tailpipe exit a bit of a problem.I like the idea of a y pipe from the headers joining into a single Flowmaster. I'll have to crawl underneath and decide how to route it.
Thanks again!
 
I have a customer at the shop who is chomping at the bit to get rid of those silly headers....we were going to run GM center dumps, but they have been discontinued...


Sanderson, here we come!
 
OK heres some pics of my dual exhaust that the PO did. its just about time to replace it and i will probably go single with Y pipe. i run the chevy ram horns and the passenger side comes down and crosses over in front of the sump of the oil pan. my set up probably would not work with a rear fuel tank in the way. good luck with your choice!
Picture 003a.webp
Picture 001a.webp
Picture 004a.webp
 
I'll post some pics up of my dual system.. which is routed totally different than Lone Gunman. there are pictures of my headers - not block huggers - (see the paint job thread that failed big time recently) already.

anyway, I never realized there would actually be an exhaust system that would have 1 pipe on 1 of the sides make a big ass 90 degree turn under the body (across you tranny, t-case, oil pan or whatever, but right in the way of heavy stuff to work on) and then make another big ass 90 turn and run all the way back. in comparison, I think mine is pretty cleanly done from what I can tell.... out headers down at slight angle to level and straight back to under the doors into muffler and out muffler then the 1 turn too exit out right in front of the rear wheels. both are run the same on each side. system uses 2" exhaust. my heat issues are only at the headers in the floor boards, not at mufflers.

muff1.jpg


muff2.jpg


thats it.. simple and clean and short it seems.

BTW, I do have an auxillary tank in the back...
 
Last edited:
Mufflers located in that position have proven time and again over the years to not be very resilient to rocks... ;)



How much inward travel is left on that rear drive shaft?



Seems pretty close to being bottomed out. :eek:
 
well... I figured if anyone would see something amiss.. it would be you :) which is fine by me as who knows what else lurks here

anyway, I freely admit, I am not as agressive as you on wheelin, so do not know if I will get into the kind of situation where damage might be done to that area? I guess time will tell with the mufflers.

as for the the rear shaft.... maybe 1.5". it is a custom shaft bt Drive Line Services of Ventura (so it says on the sticker). how much should it have?
 
It could be something with the picture, but the slip end of that shaft appears to be very close to the end of it's travel...guess I am used to seeing that piece further away from the tube....If it works, WGAF right? :)


:beer:
 
that is certainly out of my scope of knowledge for sure... I just know that I see about 1.5" of grease travel and available room before that shaft slides back and bottoms out. but I would not know if you need like 1 inch or 5? I see no damage or wear and tear on either end like it is slamming or bottoming out either.
 
why do you need dual exhaust? just more pipe to find room for....

I run block hugger headers, into a y pipe and straight back, flowmaster is tucked up and then exits out the pass side rear. I have a rear conferr type tank too. My advice, find a good exhaust shop in your area. A good exhaust guy can do it, the guy I went to did a sweet job, it cost me about $500 though....

Noah
 
well, in my case it came this way and since it is not broke.... WGAF as Poser said..


that being said, for my own education/understanding on exhaust (a new topic for me), would there not be be a power loss to have 2 pipes come togther into 1 then exit? it seems, each header pushing out exhaust into its own dedicated pipe that then merges into 1 pipe for both would cause eddies and currents and bottle neck/back up the flow out? i read here several people claiming use of the 'y pipe' setup like this and it seems normal... but it seems counter logic to me from what little understanding I have on the topic? it is like 2 full size streams dumping their content into the size of 1 stream.. which results in back flow and backup. but in the case of exhasut... no place to go as it is enclosed so you just build up pressue until it can exit? or is the reason just simply it is easier to route and manage with 1 pipe 1 muffler?

also, even if my setup is asking for muffler damage, and you wanted to go to muffler placement that is more protective like Lone Gunman has, why would you ever cross the pipes over to 1 side and route them out? why not route them straight out on their respective sides and not put those major bends in it and put it around areas (by crossing over often worked on components) you may have to work around? I could understand IF something was blocking the exit.. but there doesn not seem to be and in many FJ cases, would not be.

thanks in advance for the education. just want to get a grip on some of the fundamentals (short routing? less bends? placement? 2 pipes or y pipe, etc.)
 
Last edited:
wantatlc said:
that being said, for my own education/understanding on exhaust (a new topic for me), would there not be be a power loss to have 2 pipes come togther into 1 then exit?


You can talk about the dynamic reaction of air traveling in an exhaust system until you are blue in the face, and at the end of the day, you are not EVER going to feel, in your ass, any difference between a dual system, and a well set up single, in your specific application.



wantatlc said:
also, even if my setup is asking for muffler damage, and you wanted to go to muffler placement that is more protective like Lone Gunman has, why would you ever cross the pipes over to 1 side and route them out? why not route them straight out on their respective sides and not put those major bends in it and put it around areas (by crossing over often worked on components) you may have to work around? I could understand IF something was blocking the exit.. but there doesn not seem to be and in many FJ cases, would not be.

If oil pans are “often worked on” then you need to find a new mechanic. ;)


Lay under your truck and tell me where you are going to route it down the passenger side of the truck?


There is a transfer case in the way bud.... ;)


:beer:
 
Back
Top Bottom