Factory hand throttle?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2007
Threads
7
Messages
73
Location
Palo Alto (and Oakhurst), CA
Website
www.dimebank.com
My 7/69 came with all the "standard" improvements of the era, including a Rochester carb and Delco distributor. There are also the remains of a hand throttle - the cable is still there and makes it most of the way to the carb :crybaby:

The bracketry on the carb is a complete botch, and the carb is going to get swapped our for a factory unit one of these days. So I don't want to reinstate what was there - but would rather come up with something that is independent of the carb itself.

My understanding is that the factory hand throttle on the BJ went to the pedal ... could someone point me at photos of this arrangement? I'd like to clone it, or find a used one...

Thanks,
chris
 
I just recently bought the whole assembly from a MUD member including pedal.

The pic shows how the cable attaches to the pedal.
78handthrottle0041.webp
78handthrottle0040.webp
 
I was able to buy the hand throttle like Coolerman (I think it was from a 60 series), but I modified my existing accelerator pedal with the throttle position switch (TP) paddle on top. I just cut a slot for the cable and filed a square hole for a nylon insert (in the TP switch paddle). Works great. I also mounted the knob on the outboard side of the steering column, because it's very easy to bust your knuckles pulling on that parking brake handle with the hand throttle right next to it.
 
The cable is here (#6; SOR page 42). They have later models also. You can fab your own brackets (#48 and #21). :) Here's a firewall bracket: 042-21B-U U CHANL PEDAL-
3/69-9/73 USED

042E.gif
 
I like my hand throttle :D got it and a used pedal from SOR

the only thing I would do different is buy a NEW pedal

the rod (to the right of #8 in the sketch) that attaches the pedal to the firewall bracket acquires grooves with time and this leads to the pedal being able to wiggle from left to right
 
Sweet! Thanks for all the responses and especially photos. I had seen the SOR diagram before but couldn't quite turn it into physical reality. The PO of my truck mounted a twist-lock throttle cable in the dash next to the choke - now I need to connect it to the pedal.

(Phew! SOR wants $90 for a new throttle pedal!)
 
I like my hand throttle :D got it and a used pedal from SOR

the only thing I would do different is buy a NEW pedal

the rod (to the right of #8 in the sketch) that attaches the pedal to the firewall bracket acquires grooves with time and this leads to the pedal being able to wiggle from left to right

You can use some nylon bushings, (like door pin bushings), or brass bushings to take out the slop caused by the grooves. You may have to drill out the bracket holes a bit to accommodate the larger bushing outside diameter. My OEM pedal is grooved, but the 'new' one is not. See pics for the grooves and pics of restored brackets courtesy of AAtlas1x.
P1010033.webp
PC210021.webp
P1010085.webp
 
You can use some nylon bushings, (like door pin bushings), or brass bushings to take out the slop caused by the grooves.

I used wider than OEM washers; that helped :D
 
I just finished tack welding my grooves then carefully smoothing the welds
with a grinder and lastly a micro flat file.

Interesting that of the two pedals that I have, the one that looked to be in the best condition (nice looking OEM plating) had the most "wallowed" out pedal shaft holes on the firewall bracket.

So I used my old crusty looking bracket and spring. No more wobble.
 
Last edited:
I just learned something in this thread. My hand throttle is on the dash next to the choke, and goes straight thru the firewall to the carb. Even though I am running a Holley, it hooked right up. I had no clue there was a version that went to the pedal.
 
Kinda hard to tell from the picture but I discovered these holes get enlarged thus joining the shaft grooves in creating pedal wobble.

The unworn portions of the pedal shafts I have are 8mm and 7.62mm in the grooves. The most worn area of the pictured bracket is 8.62mm. Losta wobble.
IMG_2457.webp
 
My manual throttle is hooked up the same way that lc69hunter is hooked up. I'm also running a Holley 2 barrel carb also.
 
I just learned something in this thread. My hand throttle is on the dash next to the choke, and goes straight thru the firewall to the carb. Even though I am running a Holley, it hooked right up. I had no clue there was a version that went to the pedal.

Believe it 69 was the last model year the hand throttle was standard on the land Cruiser. Believe it was also last dash mounted knob. Not sure after 69 how Toyota determined which one's got a hand throttle. Stripped the excelerater and hand throttle from a late model 4X series that had a PTO winch. If that is why it had a hand throttle.:meh:
 
My 71 has never had one, as far as I can tell. It is a USA model.

Don
 
I made one with a choke cable, worked pretty well but would stick. I need to revisit it with a nylon bushing. Nice to have though.
 
I thought all markets got a hand throttle we always got them every 40 series I've owned (1976, 1978, 1982, 1983) has had one the same as in coolermans pics other than our trucks are RHD

My 71 has never had one, as far as I can tell. It is a USA model.

Don

My 9/67 had the hand throttle in the dash. My 10/69 doesn't. US market had 3/69 to 9/69 two barrel carburator. If those had a hand throttle unsure of. So 3/69 or 9/69 was most likely the end of the hand throttle here.
 
Yes it's called .... Cruiser control

I use it to relax my foot on long drives...

I have on veteran knowledge ... they set the throttle ... seat belt the steering wheel and let the cruiser control take you across the desert :)

I do not think I will go that far
 
Back
Top Bottom