Engine rebuild!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 9, 2004
Threads
101
Messages
1,454
Location
The West
hey all. About how much am i lookin for an engine rebuild? It is a 77 2f motor. It runs fine, but i am going to be taking it to college and wherever i go as my only dd and want to make sure it lasts w/ out probs for the next umm, 4 to 5 years and beyond. I love my baby , so again how much am I looking at. I wanna redile the speedo and start like bran new again so i don't have to worry about the motorcopin out on me at a random time. I don't know the miles. It was swapped in my truck god knows when ( during last two owners) and it was done right, but there are unknown miles and im scared. If not total rebuild what should i rebuild on the motor and how much and what is best to make it purr like a kitten. I live in the Bay area ( livermore, pleasanton, tracy, dublin area) so if anyone knows any one who does good work and resonable price. Point me in tha right direction! thanx,
Rachel
 
I would start by running a compression test, wet and dry. You can then better gauge where you are with your motor now and what steps to take on a rebuild
 
Answer on the rebuild of a motor is easy, Mudrak's in Sonoma. If you can remove it, he can do it as a bench job or he can remove, rebuild and replace. He knows the 2f's very well.

Now do you really need a rebuild. Start with a compression check, as mentioned before, then proceed from there. Mudrak does general repairs as well including tune ups. He can give you an honest opionion of your motor and how you should proceed. From the Livermore area he is a 1 hour 15 minute drive. He can be reached at 707-996-5272.
More locally in Concord, there is a shop called Toyota Pro. They seem to always have a landcruiser in their shop general service to engine rebuild. I have friends that have there toyotas worked on there and have been pleased.

The cost to rebuild my 2F was around $2000.-2500+ for the parts and machining (I try not to add up all my receipts as it scares me). My nephew did the removale, disassemble, reassemble, reinstall at the high school auto shop. If it had to be sent to a shop to be redone the cost would of been between $4000-$4500 or more.

If you are considering a chevy 350 swap the cost can be about the same. Mudrak does the 350 swaps as well and so does Breath of Fresh Air in Concord/Clyde and there is another shop in Gilroy.

Do some home work first and then decide on how to proceed.
If you have any direct questions PM me.
Dave
 
ok what about this. New 2f engine from spector or something? How about that if i decide to go rebuilt instead of actually rebuilding it. Its only roughly 2K there. What do yah think?
 
yeah i have the whole cooling system restored and rebuilt. Rebuilt carb. Im getting a new 5 spd conv also and maybe pwr steering. If i can fit it into the 5k budget. So i am just wanting to rebuild motor or figure how many miles are on it or how warn it is so i know and know how far to push it. I will take it to get compression and al those tests done. where in livermore do you think might be a good shop to have that done by.
 
Personal opinion, I would do a compression check first and then decide if it really needs it. Another thing to concider: does your cruiser run hot..smoke on initial starts?

I believe the engines from sor.com have warranties which can be a good thing and better you at least live in the same state.

I've heard good things about Mudrak so I called one time when trouble shooting a problem, the guy knows his stuff was my first impression.....funny thing was he was coming from a trip in Nevada going back home. He took the time to answer my questions....and answered them as if he had a manual in his hand.
 
wow thats cool. Yeah i ahave heard alot about mudrack. People who have ahd these things done on their cruisers at mudrak how much were they : power steering conversion, 5 spd and fuel injection? just curious.
 
I have also had good experience with Gary Kardum at Mudrak. You can't go wrong there. There is another shop in Concord I've heard of called "a breath of fresh air auto". I've never used them, but drove by once and there was a couple of FJ-40's outside.
 
Yes i think i will check them out. Does the guy in concord that has the shop a breath of fresh air ; is his name Kyle? becasue he was talkin to me about how he can give me a killer deal on a h55f install! Hes awsome! anyway. any prices here of what people paid to get their engine reinstalled?
 
When my dad first bought the Cruiser, it smoked, so he did an inframe, basically rings, bearings, and gaskets. This was about ten years ago. Every year, as I'm able to, small mods have helped this thing run better and better. It runs better now than it did 8 years ago. I would echo statements forementioned about doing a compression check (easy). If your engine doesn't smoke or knock, there's no reason you shouldn't be able to get onother 5 or 10 years of dependable running. Worry about points, timing, carb adjustment, proper vacume pluming, optimum exhaust, clean oil, ect....all the basic stuff, and it'll be fine, and you can save yourself some cash.
If you're dead set on a rebuild, depending on how you go, it's prolly between $1500-$2000 for machine work and parts (if you really go crazy). A might more if you have someone else do the labor.
 
oh yeah i laugh at the though if trying to do it myself. Ive know an ok amount mechanically ,but rebuilding is WAY out of my league. u really think ( sense i don't know the miles or anything on it that i could get another 5 to ten years outta her? ) I just wish i knew what kinda miles are on her. Driving me insane!
 
i was just going to re-ring and re gasket and re-bearing, to get her on the road. but i ended up needing the head to be shaved off a little because it was a bit warped and not flat on the bottom also two of the valves were replaced, and i got all new hardend valves seats. also needed a new set of lifters, my cam was shot so i got one from someone on the forum(thanks ed :D) so my rebuid proably cost 700+ so depending on what your wanting to do with it. wether its bore it out and get the rv cam. or just rering and hone her, your still looking to spend 400 at the least...
 
The person at Breath of Fresh Air is Ron. He does the H55's in FJ40's all the time. His Primary work is in chevy 350 swaps and he does a nice job. He doesn't do much with the 2f motors except pull them out. He is a nice guy and his work looks good.

Gary at Mudraks redid my power steering conversition and Shackle reversal. What a difference. The previous owner of my rig had a bolt on shackle reversal and the car would not go straight. As far as the cost I am not sure what the power steeing cost alone. Call Gary and talk to hin about your cruiser and your plans for it. See If you can schedule an appointment to bring it up and get a compression check and review of the motor while you wait or walk around town. It will be well worth your time and money and the drive is not that far. Not to mention his shop is fun to poke around.
Gary is busy so call a head. He can probably give you budget numbers on the phone. If he isn't able to do the work with in your timeline (he is a small shop) he will tell you.
Good Luck.
 
okie,

sounds to me you need to work on your level of worrying. My cruiser has unknown miles as well, but I would still drive it everywhere. If I were worrying as much as you, I wouldn't have been to Moab twice, I would not have driven the Cruiser halfway through the country and back, and I wouldn't have had fun running 4x4 trails. It's the fun you are missing by worrying. Should something happen, yes, you will have to deal with it; but then you live a massively populated area, you'd never have to walk 20 miles. And even then, there are much worse things than a broken down car on the way to college.

Why not have Mudrak check it over and then decide what you might need. Don't attack if not broke.
 
Last edited:
74fj40 said:
my cam was shot so i got one from someone on the forum(thanks ed :D)

You are MORE than welcome. Glad to have a part in getting any cruiser running again.

Ed:)
 
i would do exactly what most of the guys on this thread said: a compression test. if you have good oil pressure and the engine runs reasonably well and does'nt smoke, then there really should'nt be any reason to restore it.
i see cruiser engines go over 250k miles at work without any problems, and some of them are'nt really that well maintained by the owner.
i can vouche for gary's (mudrak) quality of work just like the others. he's honest, reliable and does great work. and those are just some of the reasons why i started working there...........
 
something else to think about: do some homework before going with the 5 spd. are you doing it for fuel economy? if so, it's gonna take an awful long time to pay for itself.
are you doing it to increase your freeway speed with smallish tires? how about swapping out the diffs with the later 3.70s instead? that would save you a bunch of money.

i have talked to numerous people about the H55s. pretty much all the used H55s i've heard about or seen myself had some sort of issues, from gear or bearing noise to grinding into gear to popping out of gear,...........the list goes on. kinda makes you think why they'd sell the used 5spds and ship them over here, right?! maybe it's because they're completely worn out and don't want to bother fixing them but since there's a market for them over here in the USA it's an easy sale. i would only install a new H55, nothing else. period. i know it's not a cheap way to go but it's reliable. and it sure sounds like that's what you're after.
also, make sure that you consider all the parts that will have to be installed in conjunction with the 5 spd and the cost of these parts. you'll have to run a later split case, you'll need the shifters for the transmission and the t-case. also, what are you going to do about an e-brake? you can convert the split cases to a driveline style e-brake setup like the one in your 40 right now but it's gonna add even more $s to your conversion. the you have to do drivelines on top of that. you'll also need the 5spd bell housing or you could modify the 4 spd bell housing to work. there's always more to a conversion than you think, until you've done a few.

i'm not trying to discourage you from making your cruiser more driveable or reliable, just want to make sure you have a realistic impression of what's ahead if you do some of the work you're thinking about. i think that driving a cruiser as a dd is a great way to go and they are a lot more fun to drive than most vehicles. especially out here on the west coast.

georg
 
Back
Top Bottom