Engine Issues FJ45

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

That is pretty much what I figured you would have to do to make them. I looked all over for channel that closely approximated the OEM weather strip retaining channel, but I never found anything that came close. My plan B sas to make a series of "clips" spaced a few inches apart. All it has to do is retain the channel and like you said, you don't really notice it. I sold this set of doors, so now it is someone else's problem.
 
bull said:
Follow up. It is still doing it. Not sure exactly what to do now. I have replaced the fuel filter(s), fuel lines, fuel pump. I'm very frustrated with it. Here are the next steps.

Going to send the carb to Jim C.

Going to remove the tank and clean it once again.

Have you checked the carb screen recently? Where the fuel line goes into the carb there's supposed to be a fine mesh screen (sometimes it is missing) that can get clogged.

I assume you've unhooked the fuel line from the carb and just pumped into a bucket to see that there's a steady stream and the fuel filter and pump are OK. Si?
 
IDave said:
Have you checked the carb screen recently? Where the fuel line goes into the carb there's supposed to be a fine mesh screen (sometimes it is missing) that can get clogged.

I assume you've unhooked the fuel line from the carb and just pumped into a bucket to see that there's a steady stream and the fuel filter and pump are OK. Si?

Carb screen has been out several times. Looks very clean, hell the whole carb looks clean. Inside and out. I popped the top off the carbcleaned everything. Made sure it worked correctly. The float moves up and down nicely.

I put it together and drove it for 15 minutes thought I had fixed it, but noooo! Started it again after a while. The float bowl keeps emptying. When it starts to act up I kill it and pop the hood to look at the fuel level in the carb. Sure enough the bowl is empty.


I have unhooked the line and had it pump back into a gas can. What is a good measure? A cup in 20 seconds of cranking?
 
Is your gas cap vented? What style tank do you have?

Do your fuel lines run close to your engine/head?
 
bull said:
Here is a pic of the carb with gas level. It is low? Could this be it? Do I need to adjust the float level possibly?

67float.jpg


well my carb i just rtecently had put it on my truck and the guy who rebuilt it didn't set the float level right. it is 3/4 of the way up witch is WAY off. Evidently the float level should be right where you have it. thats where mine needs to be so ... thats the best i know


good luck
 
Yep, that's either a stuck float/needle valve, or inadequate fuel getting to the carb, or the float's maladjusted.
 
Fuel tank is vented.

When the rig is idling the fuel in the float bowl is right on the dot. When I drive it under a load is when the bowl empties.

I took out the needle and spring and cleaned everything. Looked good and operates normally.


Could the lobe on the cam start flattening out affecting the fuel pump?

Also how much fuel should be coming out when I crank the engine?
 
Since you found material in the tank clogging the system, cleaned it and had a grace period of 40 miles or so, I'm going to vote for krapinzetank as your problem again, before the carb or fuel pump or a worn cam. I don't know the specific amount of gas a pump should put out off hand, but I think I can put my hands on that number when I look at the manual. I'll let you know.
 
That's not a bad idea.

The fuel pump is supposed to deliver 2.22 US quarts (2100 cc s) per minute at 1000 RPM of the camshaft. (Remember, the camshaft turns 2x for every turn of the crankshaft, so that would be 500 RPM on the crank.)
 
Last edited:
The symptoms are not consistent w/ a carb problem. If there is no fuel in the carb, there is a fuel supply problem.

Krapinzetank x2.

FYI, the cam turns 1/2 crank speed, so 1000RPM camshaft speed is 2000 crank speed.
 
Thanks Dave and Jim

Once I have figured out the issue I will be sending you some carbs from the fleet..

It is hard to diagnose. At idle there is gas in the float bowl up to the dot. Drive it a bit and it starves for fuel and there is no fuel in the float bowl.

Would a faulty fuel cut solenoid cause these symptoms? Asking a ton of questions before I have to empty the gas tank again..
 
I had a similar prob with my FJ45 that I couldn't track down once. Turns out it was a pinched fuel line that was starving the carb. How or why it happened I don't know, just one of those things. Had my mechanic baffled too. Luckily I ran on LPG too or it could have been a very sad camping trip indeed!

I think I saw you had changed the fuel lines but might be worth checking how the hoses are run and held in place again.

Good luck.:)
 
I have it seen them bog down like way you discribed but it's usually consisentant. My first guess would be fuel problems too. This is a stab in the dark but since you are at crossroads I word temporarly lean towards checking the electrical system real quick just to make sure all is well. I don't have enough info that would suggest it's an electrical system issue but it sounds like you may be running on 5 cylinders at times. Double check the integrity of the sparkplugs and wires.....swap them if you have to. Good luck.
 
Last edited:
bull said:
Damn you Krapinzetank!
I'm a little confused. Didn't you already clean out the tank and blow out the fuel lines. When you blew out the fuel lines, did you see any rust come out? If so, I would replace the fuel lines. Also, when you cleaned the tank, were there signs of rust inside the tank. If so, I would line the tank with a tank liner like you can get from POR-15. I would be inclined to ask what type of fuel filter you are using and do you get any material caught in the screen after cleaning the upstream components. When this happened to me it was the filter (brand new, I might add). I went to a filter that had a larger area of filtration and the problem disappeared.
 
Back
Top Bottom