Cruiser Rescue Project

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 1, 2009
Threads
35
Messages
1,701
Location
South Central PA
So I was trolling CL a while back possibly looking for a parts vehicle when I decided I was not willing to go wheeling with my 97 LX450. I would freshen that up and make it a mall cruiser for another 20 years.

I still wanted to start getting off-road as a hobby, but most of the wheeling near me (PA) doesn't seem to be logging roads, it's more like dry creeks and lots of rocks. So I decided to find a reasonable Cruiser to turn into a dedicated wheeler. Here is what I found for $2500


It had been gutted and sitting for a while. Not sure what plan the PO had for it, but it's in fairly rough shape. Regardless, for the money it seemed like a good gamble ... and it has factory lockers.

I flew down to NC, kicked the tires, checked the fluids and drove it 7 hours back to PA. It made the drive without a hiccup on 4 bald ass tires. Cruise control quit about 5 hours in, but decided to work again the next day ... possibly heat related. Anyway, I'm going to have a million questions as I try and get this ready to pass PA inspection so I can at least get it on the road.

Question #1 ... The hood latch works, but the cable is out of the latch on the inside of the vehicle. How the heck do you get it back in the latch pull? I see where its supposed to go and understand how it slides in from the right and cable in the groove, but I cant seem to create enough slack to get the cable to do so. Is there a trick to it I am missing?
 
I was hoping to do some baselining while driving back to PA, but the OBDII port doesn't seem to work. I checked the FSM and the wires in the port are where they are supposed to be and I checked all the fuses and relays and they all seem fine as well.

As I said before, the truck has been gutted, so many of the connections and harnesses may be unplugged.

Question #2 ... Where does this plug into? It seems it would be important. Possible this is why the OBD port isn't working?


I can feel another connector loose behind the dash, so in the process of removing things to try and get at it to see what it may be.
 
Can you give location / context to that plug in pic?

Offhand I see a stereo connector, but without location I don't want to die on that hill.

Sounds like a decent $2500 spent for exactly what you want to do with it.
Also, if you hit copart they're wrecking a few modded 80's, one has lots of good ARB parts (bumper, etc)-it was either green or black & seemed like it was E of the Mississippi.
 
Been scouting CoPart and Ebay on and off for part outs.

The connector is under the dash just above where the gas door release is located. I felt around for a mating connection. but can't find it blind. I remember reading through the FSM and thought I saw a PIN out code for it, but not 100%. Not sure I can contort myself upside down to get under the dash in the footwell ... getting older sucks.
 
Bump for any help on the hood release or wire harness questions
 
Removing the knee panel from just below the steering column will help tremendously both of your issues. And, as you go through this 80 you will find many unused wire connectors.
 
Panel removed ... makes it no easier to get the hood cable in the lever. Can the metal piece come out of the plastic panel? If so, how?

Also, with the panel removed all I see is a metal bracket from behind where the plastic panel was ... no wiring access there. I will try and remove the upper panel around the steering wheel and see if that gives better access. Had my 14 yr old son squirm under the dash, but he didn't see a place for the connection to go, but if it's not an xbox or PS4, he likely doesn't know anything about it.

Truck is getting a new windshield tomorrow and new 305/70R16 tires all around today.
 
Created a new thread hoping for some solid guidance on the wiring connection I posted above. Still hoping someone that has done the hood cable can help with that too. Please see the above posts for pics and such.

The new General 305/70R16 tires on the stock rims are a real nice fit and soooo much quieter than my knobby retreads on the LX450. I may swap the wheels once they are cleaned and painted since the Lex still has the fender flares, running boards and mud flaps.

Here is today's stupid issue ... so to pass PA inspection you need MANY things. One of them is a windshield cleaning system. Super simple right? Not so much. The 97 I have has the reservoir and a working pump, even has a line that the washer fluid squirts out of ... what it doesn't have are the sprayer nozzles to mist the windshield. WTF!! To add a layer of FAIL, I just had a new windshield installed today, but dropped off my LX450 to pick up the Cruiser, so I'm not really sure where they belong. I thought the hood, but there are no mounts or holes. Guessing the PO may have damaged the hood and bought an older year as a replacement?

Starting to think I should have spent another $3k and gotten a non-F*&%ed truck, but those factory lockers sucked me in.

Forgot to mention ... called Slee today and left a message (cool ass English accent on the answering machine - reminded me of the Accountant movie). Need a bumper to pass inspection and this WILL be a wheeling rig, so may as well start putting on the right parts.

If I can become a bit proficient in servicing these Cruisers, I will sell off the vans we use for deliveries and have 2-3 Cruisers as our delivery vehicles. The vans are horrible and constantly breaking down. We rack up maybe 300-500 miles per week, so at least I know the cruisers will take the miles, but the fuel will hurt my feelings.
 
Last edited:
Finally made some progress ... new windshield installed

After days of headache, I found the 2 screws that hold the metal retaining piece for the hood latch to the plastic kick panel. Removed those, slid the metal out and mounted the hood cable correctly. Small win, but felt good.

Now new issues ... need to order a new bumper for inspection, spoke with Christo @ Slee about the Short Bus, need to see if one is available next week. Here is the question ..

Do I need the mounts that are shown here connected to the frame or does the Short Bus connect w/o them? I read the directions, but it wasn't clear to me and had very few pics.

Now more win ... 305/70R16 tires mounted. Generals I believe. Nice a quiet on the road.

More bad, this is really stupid too. So the hood fits, but when driving it raises up at the front corners. I can't get it to sit on the stops when closed either. The front fenders have some dents, but not bad enough to mess with the top lines and no wrinkles where they bolt up. I've adjusted the hood latch several times, but can't get it low enough to fit tight.

Regardless, here is the dumb issue. There are no wiper spray nozzles in the hood. WTF is that about? Is it possible that it's an older hood and the nozzles were elsewhere or is the setup different from that on my LX450?

Here is the hose for the nozzles (drivers side by the brake booster) ... the pump works just fine.
 
Removed parts of an aftermarket alarm system as well

This is the positive terminal ... thinking some of this crap in the alarm system. Tried to remove it, but the terminal connector started to sheer off. Can't anything be easy?

Last two issues ... still no power to the OBD port. Need this for inspection for sure.
Anyone have any input there?

Took a few pics of the back of the fuse panel ... bottom 2 slots empty, should there be plugs in those?
 
Most if not all aftermarket bumpers will mount directly to the frame horns, no brackets needed.

Wires on the positive battery post look to be the OEM fusible links. They need to be there and a good idea to replace them. They could be related to your non-functioning ODBII port. The set (3 wires) is under $15.

With no holes for windshield washers the hood more than likely has been replaced with a non-OEM version. Search the forum for "windshield washers" or sprayers/squirters etc. There has been a few threads in the past where people have replaced them with those from other Toyota models or aftermarket that have improved function. Should be as easy as drilling some new holes with the squirters being attached with clips.
 
Thanks PPC ... will do research on that asap/
 
unrelated to that - what is used or have members used to fill in the fender flare holes?
 
Does anyone know what fuse should control the OBDII port? I haven't seen anything here or on youtube. The lighter socket is functional in the truck. I've purchased a new fusible link, but the truck starts and runs and everything else seems functional other than the OBD port.
 
Today was not a good day. Fist time I've had a chance to spend some hours on the new Cruiser in a while. Work is kicking my ass and the LX450 being down, possibly for the winter, has me focusing on trying to prep this truck for PA inspection (OBD plug in and code reading). I currently am having the following issues"

- OBD port does not power the scan tool

Pulled codes today for the ABS with the E1 to Tc jumper and just got a solid ABS light, no blinking or anything,

Airbag light - code 31

Cruise control light - code 14

Got these lights while trying to pull the ABS code ... going to do research in the FSM as soon as I can, but any help is appreciated and I just ran into this today as well when I drained the radiator after seeing some brown int the coolant overflow ...


This truck may be fu*&ed, how is it ever still running without overheating? The metal lines seem clear, but the radiator and hoses have crap all through them. Drained it, flushed it and now running just distilled water and will purge again in a few days. I've never seen anything like this before o_O
 
Oh yeah, you're going to either need to plan ahead where you dump & refill a few times (I'd gardenhose the crap outta that for awhile, then move over to distilled for a few flushes), or you're going to have a 'rusty streak' in your driveway for ~6mo.

A 60 my buddy bought had this & we shoved a garden hose onto one of those 'T's you buy from Pestone & splice inline.

We turned on the hose & something short of 2 hrs later it was at least opaque, with a 25' rusty streak down his driveway. He dumped a few changes of distilled water, then he swapped in the right ratio of coolant & distilled.
 
Are you guys thinking change out the radiator and hoses too, or just many flushes?

Is the drivers side the input or outflow for the radiator? In case I want to feed it water while its running.

What caused this in the first place? Was it just sitting a long time or did the PO swamp the truck in a mud puddle?

Seeing threads elsewhere about using CLR. I will look into the Prestone T as well. Crappy part is that I live in the woods and am not on city water, so any draining will likely need to be done at work.
 
Back
Top Bottom