Birfield Carnage!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Landtank, are you going to try the ebay birfs?

They are already on their way. Last week in bitter cold my right one clicked first thing in the morning and It's the original and has wear in the joint. I also picked up 2 spindle bushings that will go in as well to get a good idea of how these perform. They'll go in while on vacation in February. I'll keep the originals around for spares should one fail.
 
I'm very tempted to try those as well, but I'm too paranoid I think. I'll probably just go with Longfields and I think I can reuse my ABS ring.
 
I installed one for another member and it looked good. But I'd like to get the ABS rings from IronYuppy so my originals will be ready to go if there were to be an all out failure.

When in use the truck receives alot of miles and then in the summer it will see some trails. I think I can give them a good workout in a relatively short time.
 
Last edited:
Go ahead and get them. Like I said, I think my rings are good enough to reuse as they weren't tripping my ABS light. I'll be curious to hear how those work out for you. You know I just spoke to Slee and they have an aftermarket birf that is selling for $250. They claim that it is equivilant to stock and should wear a lot better than the longfields for highway use. Thats where I am leaning right now.
 
I didn't know Christo had after market birfs. The wear issue is why the Lonfields aren't on my list. I had originally decided on OEM but right now the cash for them isn't available and I'm hoping for a few years out of these.

My call on it was that the OEMs lasted 122,000 miles before clicking. I'm betting the longs will last at least that long with proper maintenance/packing every 40K. The longs are half the price.

Properly maintained every 40K the OEM units might last 240K or so. With the rash of these being changed out at ~120K... I think that must be the limit without properly repacking or something.

Oh, as far as I'm concerened, clicking = worn out. Others swap sides/repack/etc...

YMMV.
 
Littleboss on this list has 20k miles on a set of Longfields with major clicking. I think they wear pretty fast and would only run them with a part time conversion. I'll be curious to see how the cheap birf replacements do.
 
Littleboss on this list has 20k miles on a set of Longfields with major clicking.

Isn't this your answer?

I spoke to Bobby Long two days ago and he recommended against buying his birfs if I planned on highway driving. He insisted that they would last 1/2 as long as OEM and by that he meant 60,000 miles.
He also said that they were a lot harder to break.
 
They wear faster because they are softer, not harder...they bend before breaking, hence the toughness is there in longs. This also allows normal wear patterns to be accelerated...not rocket science ;)
 
They wear faster because they are softer, not harder...they bend before breaking, hence the toughness is there in longs. This also allows normal wear patterns to be accelerated...not rocket science ;)

i know its not rocket science, what i am saying is even bobby is just guessing. no on has actually got a set to click or wear out yet... i have broke 2 stock, havent heard of anyone breaking or wearing out longs... just sayin...
 
Properly maintained OEM birfs shoud be good for at least 200,000 miles, probably a good geal longer. I would not be surprised to see them go 300,000 miles.
 
Properly maintained OEM birfs shoud be good for at least 200,000 miles, probably a good geal longer. I would not be surprised to see them go 300,000 miles.



Under stock tire/gearing and "normal" use conditions?
 
Under stock tire/gearing and "normal" use conditions?

I would say even more agressive than that.

Mine have ~150,000 on them and they are in excelent condition. Almost half of that mileage has been with a supercharger and 3/4ths of it with oversize tires and almost all of it with a lift.
 
Update:
Everything is fixed! This weekend I finished putting together (again with the help of thekirk) my front axle and spared not expense. It now has all new bearings and 2 new birfs from Slee Offroad. Thanks to everyone for all your help. Now if I just keep proper service intervals that axle should go another 200,000 miles.

a couple of notes:

The Slee Birfs looked slightly different than the OEM, specifically the shape of the inside of the star was different.

It took more force to install the inner axle to the new birf than it did with the OEM birfs. This delayed us quite a bit because we were expecting the clip to slip in place like it did on the OEM. We used the two screwdriver method to press the clip into the grove but eventually had to use a steel hammer on the top of the axle to get it to slip into the birf.

The Slee aftermarket Japanese made birfs do not come with ABS exciter rings. I used a steel shaft with a small (1/4 inch) square head and hammered it in at a 90 degree angle to the birf stub axle. It took a couple of minutes to remove each ring. I then heated the rings in water on the stove and installed them onto the birfs which I had left in the freezer over night. It was a snug fit and I used a steel happer to gently tap them into place.

The Slee Birfs also required the updated drive flange.
 
on the OEM birfs on both my 80 and 62 the clip was a B!7@h

heard a very neat trick on here not long ago, use a zip tie to compress the clip and slide the axle in, after the clip gets in the zip tie is knocked off kind of like a piston ring compressor
 
If I didn't have a second pair of hands around that trick would have been real helpful. I'll have to remember that.
 
Here's a gratuitous speculation.

Although its tough to tell from the photos, its possible that the work was done, and the technician only filled the bell with grease. But you have to wonder if it was the proper grease. The moly-disulfide based grease is apparently designed for use in high load situations with long intervals between repacks. Its somehow "stickier with respect to the metal" than other grease bases. And my remembrance is that my moly grease was an ugly gray/green. The grease or whatever showing in the photos seems to be a very different color.

We've had lots of speculation on this board on whether enough grease to do much gets in from filling the knuckle through the fill hole, and without looking for stats, there seems to be consensus that not enough does get in....in fact, precious little. So I'm saying that I think a failure to fill the knuckle wouldn't necessarily cause this failure.

My guess is that the tech did a half-assed repack without completely filling the bell, and further, I'd put the odds at better than 50/50 that he didn't use the right moly based grease. Add to that the failure to fill the outer housing and there you go. [actually, one further wonders that if he used the wrong grease, maybe it would exit the back of the knuckly with more ease, and end up dry sooner than the moly based would].
 
Back
Top Bottom