BEST H.E.I. Dist?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 13, 2006
Threads
45
Messages
86
Location
Sabinal, TX
Website
www.brushyhill.com
Now I'm considering going with a HEI dist. in my 02/75 FJ40- for better performance and gass consumption. I'm looking hard at the D.U.I. HEI distributor, but a friend is pushing "MSD." What, in y'all's experience is the BEST H.E.I. distributor for a '75 FJ40 and WHY?

Where Can I find the best price for what you recommend?

Thanks for all of y'all's advice!

Nick
Austin, TX
 
IMOP the best HEI is not a HEI........its a fj60 distributor, coil/ignitor, matching side plate, its a drop in swap, its toyota, its waterproof and the gear won't come and kill your motor.

should be able to get all the bits for under $200
 
I've been using the DUI HEI for almost 4 years without any issues of any kind. My engine runs smoothly through the RPMs with no hesitation and idles at 650. I'm not sure if you have talked with DUI, but they are great people and very knowledgeable. They back their hardware 100%. If you do go DUI HEI then I would recommend that you purchase directly from them. I say this because they will want to know how you drive, DD or trail rig or both. They will set the advance curve to meet your application. Unlike FJ40/60 distributors, you can get replacement parts at any auto store, when and if you ever need them. It is a simple drop in that requires one 12v wire, which is a far simpler conversion that any FJ60 swap. It also gives you an output line for a tachometer. The issue of gear fracture on HEIs distributors is not found on DUI HEI distributors because they build them better. They will tell you that no customer has come back with a gear failure issue. You install it per their instructions, set the timing and drive. You will not have any issues with it. I made the right choice.
 
Last edited:
well the fj60 set up is pretty darn easy.

also the fj60 set up does give you a tack hook up, as the fj's all had tachs.

never had a problem finding fj60 cap/rotors.......also never needed one out of the blue.

but to each his own, but I beleive a Toyota part in a Toyota motor is better then a chevy part in a Toyota motor.....;)

bsevans said:
I've been using the DUI HEI for almost 4 years without any issues of any kind. My engine runs smoothly through the RPMs with no hesitation and idles at 650. I'm not sure if you have talked with DUI, but they are great people and very knowledgeable. They back their hardware 100%. If you do go DUI HEI then I would recommend that you purchase directly from them. I say this because they will want to know how you drive, DD or trail rig or both. They will set the advance curve to meet your application. Unlike FJ40/60 distributors, you can get replacement parts at any auto store, when and if you ever need them. It a simple drop in that requires one 12v wire. A far simpler conversion that any FJ60 swap. It also gives you an output line for a tach. I made the right choice.
 
Well, I must agree with 'Pimp because I am doing just that, but to answer the question about the "best" HEI. I think getting one out of a truck is better than gettting one out of a Camaro. Of course the springs and weights can be changed, but the one out of the truck should be curved more appropriately for the LC.

JMO

Ed
 
Landpimp said:
well the fj60 set up is pretty darn easy.

also the fj60 set up does give you a tack hook up, as the fj's all had tachs.

never had a problem finding fj60 cap/rotors.......also never needed one out of the blue.

but to each his own, but I beleive a Toyota part in a Toyota motor is better then a chevy part in a Toyota motor.....;)
That Toyota motor was originally a chevy. Toyota modified the chevy motor to what you see under the hood of your rig. It is well known that Toyota used the Chevy I6 as the basis for the design of the F/2F engine.
 
Horitexan said:
Now I'm considering going with a HEI dist. in my 02/75 FJ40- for better performance and gas consumption.

Save your money. Uness there is something wrong with your ignition, changing it to any kind of $$$ ignition won't do anything for performance or gas consumption. The only thing it will do is empty your wallet.
 
Thanks y'all- I appreciate all the info. I've been leaning towards the DUI anyway and I think that's what I'm going to do.

Pin_Head - My ignition IS messed up. The igniter went bad (before I bought it) and the ignition system has been 'rigged' to run but doesn't run very well at all. That's why I'm contemplating the swap. I've gotten lots of help and opinions on here but the majority have recommended the same as my friends here in Austin and down in S. Texas, where my LC is- switch to a HEI. I wish I didn't have to, but I'd rather put a new system in than try to revive one that's quickly dying. I really appreciate your point of view, though. Under other circumstances I'd whole-heartedly agree. Thanks!

Nick
 
bsevans said:
That Toyota motor was originally a chevy. Toyota modified the chevy motor to what you see under the hood of your rig. It is well known that Toyota used the Chevy I6 as the basis for the design of the F/2F engine.
And the HEI was not used on the original six that toyota used as a starting point for the cruiser six...

From your logic, are Jeep parts better on a cruiser than cruiser parts??


I am not a big fan of HEI stuff just because of the headache I went through trying to get one to work fully..

That being said, the HEI that Mudrak or DUI sell is a good unit. But honestly, most of the time I think a more simple Dist is a better one.. Less failure points and easier to fix out on the trail.
 
That unit looks identical to the pertornics setup in my F engine.

I was running points when I first put my PIG on the road. Ran across the pertronics setup in the parts truck I bought.

Swapped points for the pertronics setup and there was no looking back. The only item I am missing is the coil. Still using the stock coil, wanting to upgrade if necessary?

Truck runs pretty good but I still wonder what would happen by adding an aftermarket coil that is hotter?

Chuck
 
Yotahilux said:
Truck runs pretty good but I still wonder what would happen by adding an aftermarket coil that is hotter?

Chuck

Nothing would happen.

The coil doesn't determine how "hot" the spark is; plug gap, compression and air/fuel load do. "Hotter" or higher voltage spark doesn't mean more power or more burned fuel. A high voltage has a down side: insulation breakdown and unreliability. This is why the manufacturers only use the minimum voltage necessary to make a reliable spark. There is no up side to a hotter spark than necessary.
 
hey........I think I know that already, I aint exactly a newbie :D

but HEI chevy crap is not the same as Toyota

bsevans said:
That Toyota motor was originally a chevy. Toyota modified the chevy motor to what you see under the hood of your rig. It is well known that Toyota used the Chevy I6 as the basis for the design of the F/2F engine.
 
Pin_Head said:
Nothing would happen.

The coil doesn't determine how "hot" the spark is; plug gap, compression and air/fuel load do. "Hotter" or higher voltage spark doesn't mean more power or more burned fuel. A high voltage has a down side: insulation breakdown and unreliability. This is why the manufacturers only use the minimum voltage necessary to make a reliable spark. There is no up side to a hotter spark than necessary.


OEM Toyota 20,000 volt coil should be adequate so long as the coil windings and all associated wiring and connectors are scrupulously kept in new condition, plug gaps are square, clean , and correctly gapped to specification, point gap is kept to factory spec. and contact points are as new and correctly squared with each other, and so long as RFI or resistor sparkpugs are not used to increase voltage drop in the secondary circuit and reduce static interference in any installed radio receiver.

Or a hotter coil can be installed. :)
 
honk said:
OEM Toyota 20,000 volt coil should be adequate so long as the coil windings and all associated wiring and connectors are scrupulously kept in new condition, plug gaps are square, clean , and correctly gapped to specification, point gap is kept to factory spec. and contact points are as new and correctly squared with each other, and so long as RFI or resistor sparkpugs are not used to increase voltage drop in the secondary circuit and reduce static interference in any installed radio receiver.



So are you saying a perfecet operating scenario? ;)
 
Poser said:
So are you saying a perfecet operating scenario? ;)

Yessir, I am ;) Thank you for making simpler my overly worded descriptive.
 
honk said:
OEM Toyota 20,000 volt coil should be adequate so long as the coil windings and all associated wiring and connectors are scrupulously kept in new condition, plug gaps are square, clean , and correctly gapped to specification, point gap is kept to factory spec. and contact points are as new and correctly squared with each other, and so long as RFI or resistor sparkpugs are not used to increase voltage drop in the secondary circuit and reduce static interference in any installed radio receiver.

Or a hotter coil can be installed. :)

My personal experience is that Toyota does not install substandard or marginal OEM parts. They put a lot of time and money into engineering and you second guess them at your own peril.
 
Pin_Head said:
My personal experience is that Toyota does not install substandard or marginal OEM parts. They put a lot of time and money into engineering and you second guess them at your own peril.




I do not think that second-guessing is the intention.




The fact that rarely if ever is there a perfect-world operating condition is what I gathered from it, which is a fact, dealing with 30+ year old trucks, most likely operating an original distributor that has not seen any attention in its life. If that is the case and the distributor bushings are out of spec, there is no amount of external ignition pieces that will bring it back to speed, unless it is rebuilt....
 
Back
Top Bottom