AC Problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Why is nobody mentioning the sight glass or the FSM? The FSM has a specific procedure for checking/adding refrigerent involving certain ambient temp's, certain engine RPM's, and MONITORING THE SIGHT GLASS (which is on the high pressure side). This thread gives me a headache...:D
(Joke; Hang in there Rod.)
 
Why is nobody mentioning the sight glass or the FSM? The FSM has a specific procedure for checking/adding refrigerent involving certain ambient temp's, certain engine RPM's, and MONITORING THE SIGHT GLASS (which is on the high pressure side). This thread gives me a headache...:D
(Joke; Hang in there Rod.)

I believe the sight glass was mentioned. Also, to do what the FSM recommends, you'd need a manifold gauge which will require spending another $100, which may be better spent to find the leak. He'll find out if he has a leak if loses pressure. I think until then, I don't know if there is anything he can do without spending more $$$.
 
Not the section I'm talking about; look for yourself. In my 91's manual, it's titled "Inspection of Refrigerent Volume", and again, lists a procedure for deciding whthere there's insufficient, proper, or too much refrigerant.

Oops, my bad.:doh: I was thinking 97. I couldn't find anything.


Well, being from Harbor Freight guarantees it ain't first rate, but yeah, it should do fine. Jesco says "Two thumbs up!"

X2
 
If you don't know what your pressure is, waiting for it to "maybe" leak out is not the answer. You run the risk of cooking your compressor to the tune of 600 bucks at least.

ASSUMING that you do have a leak, which is a really big assumption right now, waiting an undetermined number of days for a leak of unknown size to release an unknown amount of pressure, so that you can overfill it again with stuff to stop the leak, makes no sense whatsoever.

IF you have a leak, the sealer stuff might stop it, but then you still have no clue what your high side pressure is and you might still have this problem. IF you have a leak and it needs to be fixed, you'll have to take it to a shop anyway to get it evac'd and recharged.


Since you seem to be determined to do this your way, at least bleed some pressure off before you add the next can..............
 
:D

FWIW, in his other thread, he never was able to find the sight glass.

I thought most of this sounded repetitive.............

https://forum.ih8mud.com/showthread.php?t=158096

He even said that he let the needle get into the overfull area.......

Man, you guys are really grinding that ax down to nothing. FYI I learned a lot from the other thread including were the sight glass is. Next to the battery right under the fender wall.


OK, anymore shots, keep em coming.:flipoff2:
 
Sheesh. I have a similar issue and after reading this thread, I can see why my thread didn't get much love... :eek::lol:

https://forum.ih8mud.com/showthread.php?t=169027

This thread has been quite helpful for me though (believe it or not) with everyone's suggestions and info.

I'm off to see if my LC is *really* actually not overheating...

-Ferg-
 
I seen many post about the Blue Fan Clutch and as I said earlier I intend to change mine. Without having any over heating problems why should the Fan Clutch be changed? My truck runs great and I have always been a fan of "If it is not broke don't fix it". Is the stock Green Fan Clutch that inferior?
 
I seen many post about the Blue Fan Clutch and as I said earlier I intend to change mine. Without having any over heating problems why should the Fan Clutch be changed? My truck runs great and I have always been a fan of "If it is not broke don't fix it". Is the stock Green Fan Clutch that inferior?

If it isn't broke, don't fix it, but an unmodified stock temp gauge will not tell you that your fan clutch is bad. This may be Ben's problem, but likely isn't yours.
 
What is the temp gauge that is recommended?
 
You can modify the stock gauge very easily to eliminate the dead spot in the middle. Search for *temp gauge mod* and you should see a thread authored by Raventai with a title about 93-97 temp gauge mod or something like that.

You don't need the mod to verify fan clutch operation, but unless you check the fan clutch physically, your gauge won't show that it is bad. A modded temp gauge will show a temp spike while idling if the fan clutch is bad.
 
Cool, thanx, I'll definitely check that out.
 
around 45 psi

How did you charge your system? Did you use the system with those 12 oz. can kits you can buy...? If you did, and added a whole can, and your low side pressure was 22 psi to begin with, and 45 psi at the end, you likely overcharged your system. Low side pressures need to be between 22 and 32 psi. High side pressures need to be between 220 and 275 depending on the type of gas you added.

Also, be careful adding those cans to your leaking systems frequently...You will eventually end up with to much oil in the system. Find someone who knows how to work on your AC, has gauges, knows what the readings mean, can fix the leak(s), and can properly charge the system before it costs you in the long run.
 
I just saw details in your other post...It is pretty obvious that you overcharged your system using the cans (resulting in the 45 psi suction pressure). Starting with 22 psi you probably only needed to add a third to half can. Let out a few ounces of refrigerant...
 
Back
Top Bottom