AC Problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I think you're right about the overcharging. A while ago I posted a thread about my AC not being cold enough. I was going to take it to a AC mechanic to recharge but those who answered my post recommended that I save money and get a kit. OK live and learn, I guess I overfilled my AC. So now I am looking for someone to check my system like I originally wanted to do. I hope I haven't done ant damage to the compressor through all this. Trying to save a couple bucks = a lot of aggravation. I guess I can't catch a break.:grinpimp:
 
I'd just continue pushing the buttons until it quits for good.

If you can, pull over next time when it quits and see if the hub on the compressor is turning. If it isn't, you have an intermittent electrical problem. I'd look at the AC relay first.....

does anyone have a pic on this or can explain where it is/what to look for?
 
When your AC is switched off, the pulley turns with the belt, but the center of the pulley (or the Hub) does not turn. When your compressor is engaged, the center of the pulley will turn as well.
 
The high pressure cutout is there for a reason, so your system does not get damaged. It happens about 425-450 psi on the toyota. You probably have not done any damage to the system. Let out a few ounces of refrigerant (do not scold me I know it is not the most environmentally sound thing to do) with the truck and AC off. Or take it to someone that can let it out and recover the refrigerant and use gauges at the same time to get the pressures adjusted right.
 
Well I think my luck ran out. On a trip back from fishing this weekend the AC started to blow warm air. So I took it to a AC guy today who told me that I needed an Expansion Valve because of the pressure differences on the High and Low sides were so out of balance. He told me that he had unloaded all the refrigerant and refilled it and still could not get the right pressures. His opinion was that the Expansion Valve was sticking and had to be replaced.

Is this something I can do? I know that I will need to off load any refrigerant before I do this.
 
Let him do it. Since you will be opening the system, it needs to be vaccumed down to remove the moisture before recharging it. Good (better) luck..
 
Is this something I can do? I know that I will need to off load any refrigerant before I do this.

I've not done it, but I've reviewed the procedure and it looks doable. It's looks a little time consuming do to where it's located. I'd guess the shop time on it would be 4 to 6 hours, so could get expensive. The only problem with doing it yourself is, they may not want to evacuate and recharge the system after you replaced something on it.

:beer:
Rookie2
 
This would be a good time to replace the AC dryer too. At its age, it has probly absorbed all the the moisture that it is going to. Leaving the old one on there will likely lead to icing down the road. Only about 30 bucks IIRC......
 
ac shutting off

Same thing was happening to me. Pep Boys replaced fan clutch for $241 and blows colder at stops and stopped turning off.
 
You may be able to unstick the expansion valve by flushing the system. Be sure to get a new drier if you decide to go that route. I believe the r12 system when fully evacuated, holds 6 oz. of oil, 2.09 lbs of refrigerant at the max , and the 134a system holds 6 oz of oil, and 1.98 lbs of refrigerant max. $600 for a compressor? Wow, I will sell you one for that if you need one.
 
My AC runs nice and cold but every once in a while it seems like someone turns it off while it's blowing cold air. It immediately blows hot air until I hit the OFF button and then press the HIGH button. After I do this it stays on and works fine. Has anyone else had this happen or is my Cruiser possessed?:bounce2:


Dude, with all due respect, your posts are PAINFUL :crybaby: to go through and seem to irritate people, just my 02. I'm researching AC info , and reading all these posts, that's how I know. Waaaay to wordy, Mud should charge you per word! :flipoff2:
 
Hi,
After the long winter we had a nice day here in the Northeast, and I discovered that my A/C was not working. I followed this thread and charged the system with 12Oz 134a and oz. can of 11oz 11 of 134a with oil. A/C blows cold air now.

The sight glass is three quarter liguid. When I run the A/C I still see bubles. So it sounds like I need to fill a bit more. So here is to my questions:
1. Which is more important, the sight glass or the pressure gage?
2. to get the sight glass to go liguide, and it is 3/4 now, do I need another 12oz or a smaller can?
 
IMHO the pressure gauge is definitely more important but I am not an expert.
 
Hi,
After the long winter we had a nice day here in the Northeast, and I discovered that my A/C was not working. I followed this thread and charged the system with 12Oz 134a and oz. can of 11oz 11 of 134a with oil. A/C blows cold air now.

The sight glass is three quarter liguid. When I run the A/C I still see bubles. So it sounds like I need to fill a bit more. So here is to my questions:
1. Which is more important, the sight glass or the pressure gage?
2. to get the sight glass to go liguide, and it is 3/4 now, do I need another 12oz or a smaller can?

At what rpm's are you charging and checking pressures?

As far as "what size can?": Doesn't matter; you don't necessarily have to put the whole can in.

Curtis
 
Back
Top Bottom