ABS System delete

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Thanks, my main issue now is removing the old booster, I got it part way out and now can't get two of the bolts back into the firewall to change the alignment. I'm a couple hours into trying to remove the old booster and I'm considering pulling the entire intake manifold or screwing the core charge and cutting the old booster into pieces.
I'm over this.
I appreciate the help but no matter what I do, I can't get the bolts to line up with whatever is in/on the firewall and pass through so I can pull it around the intake manifold.
 
My issue seems to be the bracket that holds the brake pedal against the firewall, is not slightly loose since the booster bolts hold it in place.

I've got a custom cut broom stick and a 20 pound weight holding everything together.
Wish me luck, please.
 
That was the ticket
PXL_20261118_180548367.webp
PXL_20261118_181007354.webp
 
It was not the booster, my brakes still suck, I think I'm low on power to the front calipers. I'm getting a lot of travel from the pedal but it doesn't feel spongy.

Going to check the T fitting for the front brakes.

The gravity bleed went fine, got fluid out of each caliper easily.
Currently at $700 in parts:
New brake booster
New master cylinder
New front right caliper
New bleeder screws
4 quarts of fluid
2 cans of brake cleaner
Willwood adjustable proportioning valve

Stuck in Phoenix on my way to Mexico.

FYI, three years ago I tried to drive my BJ60 series to South America, 11 days in I blew my 3b engine in Yosemite, towed to Valley Hybrids, where Georg was amazing and rebuilt my transmission right away(broken crank shaft). Put my truck in a U Haul truck, drove back to Vancouver, picking up a new 3b the day I crossed the border. $15,000 later I was back in the road this time to Baja, 3 days in I blew a hard fuel line in between Jerome and Idaho Falls, Idaho, 5 days in a hotel and some parts shipped from Canada, I was back in the road.
Any day now I'll be heading into Mexico, I'll just keep buying parts.
 
I have tested power to each wheel and with a weight on the pedal and the engine running I can't move any of the 33" tires.
 
If it's been this much trouble just put it back to stock. I deleted just the LSPV on mine and kept ABS. Significant difference in braking
he's on a road trip and in another country. Returning back to stock may not be in the cards atm.
 
It was not the booster, my brakes still suck, I think I'm low on power to the front calipers. I'm getting a lot of travel from the pedal but it doesn't feel spongy.

Going to check the T fitting for the front brakes.

The gravity bleed went fine, got fluid out of each caliper easily.
Currently at $700 in parts:
New brake booster
New master cylinder
New front right caliper
New bleeder screws
4 quarts of fluid
2 cans of brake cleaner
Willwood adjustable proportioning valve

Stuck in Phoenix on my way to Mexico.

FYI, three years ago I tried to drive my BJ60 series to South America, 11 days in I blew my 3b engine in Yosemite, towed to Valley Hybrids, where Georg was amazing and rebuilt my transmission right away(broken crank shaft). Put my truck in a U Haul truck, drove back to Vancouver, picking up a new 3b the day I crossed the border. $15,000 later I was back in the road this time to Baja, 3 days in I blew a hard fuel line in between Jerome and Idaho Falls, Idaho, 5 days in a hotel and some parts shipped from Canada, I was back in the road.
Any day now I'll be heading into Mexico, I'll just keep buying parts.

That's a serious parts cannon!

So, you've confirmed that you're getting vacuum at the check valve that lives on the booster. Your calipers are bled, and i'm assuming you've bench bled the MC. The proportioning valve is something I dont have after doing the ABS + LSPV delete. I don't think that's an issue in your case but would it be possible to take that out of the equation and see if anything changes?
 
That's a serious parts cannon!

So, you've confirmed that you're getting vacuum at the check valve that lives on the booster. Your calipers are bled, and i'm assuming you've bench bled the MC. The proportioning valve is something I dont have after doing the ABS + LSPV delete. I don't think that's an issue in your case but would it be possible to take that out of the equation and see if anything changes?
Thanks!
Yes, I have vacuum, just about to put a gauge on it, but not sure how much to look for.

I have don't this whole stupid job in Phoenix, so I have my ABS unit, and LSPV and some on the lines, I would have to make a new line or two.
 
I've got 18 inch of mercury, it's not a vacuum issues.

I think I'm going to adjust the pedal stroke/plunger depth from the booster in the Master cylinder. Everyone had told me to set it up exactly as before and I did and I have the same results. Even going one turn at a time on the threads I might be able to feel a difference.
 
Man, this is so annoying. The Wilwood shouldn't hurt anything and you can open it up completely as if it's not in the system. So it can be ruled out. I'm scratching my head on this one. Short of you putting a pressure gauge on each caliper and checking the reading while someone is pressing on the brake pedal, I'm not sure what else is going on. At least it might tell you the psi reading from the initial pedal press. I got something like this long time ago Amazon.com: Strange Engineering P2360 Brake Pressure Test Gauge : Automotive - https://www.amazon.com/dp/B002VWBHWU?ref=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&ref_=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&social_share=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB The FSM does tell you the psi each caliper should be seeing.

This thread goes into caliper psi and how to make your own gauge Diagnosing brake issues / adjusting LSPV with pressure gauges - https://forum.ih8mud.com/threads/diagnosing-brake-issues-adjusting-lspv-with-pressure-gauges.962911/
 
Man, this is so annoying. The Wilwood shouldn't hurt anything and you can open it up completely as if it's not in the system. So it can be ruled out. I'm scratching my head on this one. Short of you putting a pressure gauge on each caliper and checking the reading while someone is pressing on the brake pedal, I'm not sure what else is going on. At least it might tell you the psi reading from the initial pedal press. I got something like this long time ago Amazon.com: Strange Engineering P2360 Brake Pressure Test Gauge : Automotive - https://www.amazon.com/dp/B002VWBHWU?ref=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&ref_=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&social_share=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB The FSM does tell you the psi each caliper should be seeing.

This thread goes into caliper psi and how to make your own gauge Diagnosing brake issues / adjusting LSPV with pressure gauges - https://forum.ih8mud.com/threads/diagnosing-brake-issues-adjusting-lspv-with-pressure-gauges.962911/
Thank you, I'll look into that, basically I might need something more than jacking the vehicle up and trying to turn the wheels by hand with the brakes applied.
 
I added a turn on the brake booster fork by removing the brake pedal and spinning it then relocking.
I locked up the front brakes ,I think I can live with them now!
 
I added a turn on the brake booster fork by removing the brake pedal and spinning it then relocking.
I locked up the front brakes ,I think I can live with them now!
well that's a huge improvement! Nice job.
 
Man, this is so annoying. The Wilwood shouldn't hurt anything and you can open it up completely as if it's not in the system. So it can be ruled out. I'm scratching my head on this one. Short of you putting a pressure gauge on each caliper and checking the reading while someone is pressing on the brake pedal, I'm not sure what else is going on. At least it might tell you the psi reading from the initial pedal press. I got something like this long time ago Amazon.com: Strange Engineering P2360 Brake Pressure Test Gauge : Automotive - https://www.amazon.com/dp/B002VWBHWU?ref=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&ref_=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB&social_share=cm_sw_r_cp_ud_dp_03362MPJ0CC9AGZ1CVVB The FSM does tell you the psi each caliper should be seeing.

This thread goes into caliper psi and how to make your own gauge Diagnosing brake issues / adjusting LSPV with pressure gauges - https://forum.ih8mud.com/threads/diagnosing-brake-issues-adjusting-lspv-with-pressure-gauges.962911/
I have several 80s; each has a unique pedal feel. One has the "Off the lot" feel, one is so–so an dthe other is spongy. After much (much) testing, I'm convinced there is a suction leak somewhere in the front circuit.
 
my 80 now has a hissing sound after i shut off the engine now that an aftermarket BB was installed. It's not a leak but it's definitely a new sound.
 
I recommend starting with a pressure bleed before buying $700 in parts, none of which were needed, and spend 6 days messing around with an unsafe vehicle.
Use a hose up to your ear and the other end on anything you suspect is leaking, it helps you hear.

Thank you for all the support!
 
I recommend starting with a pressure bleed before buying $700 in parts, none of which were needed, and spend 6 days messing around with an unsafe vehicle.
Use a hose up to your ear and the other end on anything you suspect is leaking, it helps you hear.

Thank you for all the support!
now you can be on your way, finally!!
 
Thanks, my main issue now is removing the old booster, I got it part way out and now can't get two of the bolts back into the firewall to change the alignment. I'm a couple hours into trying to remove the old booster and I'm considering pulling the entire intake manifold or screwing the core charge and cutting the old booster into pieces.
I'm over this.
I appreciate the help but no matter what I do, I can't get the bolts to line up with whatever is in/on the firewall and pass through so I can pull it around the intake manifold.
Too late for you, but for the next person: loosen the nut on the drivers side motor mount and jack up the engine a couple of inches. This will give the clearance you need to remove and install the booster without drama.
 
Back
Top Bottom