valves

Hi all, I’ll try to keep it short… I found a 2f to throw into my 1977. It has great compression but the valves are crazy gunky. in the last photo you can see what 3 cans of carb cleaner got my on the right half of the valves (not very good). What do you guys think is the best path forward? Just...

whats everyone using for a spring compressor tool? I am resealing a 2f engine and I need to pull the valves and clean everything.

Hi guys, I'm looking for both seat intake valves STD 1113150030 and seat exhaust valves STD 1113550030 for 1999 LC UZJ 100 4.7. I tried to contact Partsouq, Megazip, Amayama and Toyota dealer in Italy but those spare parts are discontinued. Do you know if there was an American spare parts shop...

I was swapping my old vacuum lines for fresh and snapped one of the plastic nipples off what I think is my HACV, high altitude compensator valve. I checked on mega zip to Id it, pretty sure it's th HACV, and it shows discontinued. US there a later valve I can replace it with?or am I down to...

Did some searching and couldn't find an exact match to my question. Lots of threads on how to change out rear Springs (making sure to crack KDSS valves). And lots of threads about stuck/corroded KDSS valves. One of my KDSS Allen heads on the wife's 200 is completely stripped and rusted on. I...

Looking for 4 exhaust valves for a 1KZ-TE top-end rebuild for my 1994 LC Prado KZJ78. Toyota Part #: 13715-67020. I'm finding it hard to track these down in the US - let me know if anyone has any leads!

Looking for 4 exhaust valves for a 1KZ-TE top-end rebuild for my 1994 LC Prado KZJ78. Toyota Part #: 13715-67020. I'm finding it hard to track these down in the US - let me know if anyone has any leads!

I just bought a 2018 Taco, my first, and I want to be jazzed but there is this ticking sound making the engine sound pretty ugly. I got it with 75k miles and this guy I know had his with 95k, but his engine sound like a purring kitten. My friends say get my valves adjusted, but my brother...

Just a bit of diesel trivia. I've noticed early Toyota diesel valves will say 'HZ', 'KZ' or 'L' on them which usually indicates engine family. But then I've seen pictures where they're mixed in a given engine. For heck of it, I looked up these part numbers. 2LTE exhaust valve 13715-54040...

Looking for a complete overhead set. Valves, springs, keepers, and retainers. For a 1983 fj60 2f.

So i bought a 1983 fj60 with a cracked head. The whole engine was a basket case. I got the head repaired and turns out the previous owner lost the valves. I found a set of valves from a 3fe. I dont want to do the sbc valves because my machine shop said they dont know anything about it. I dont...

I've spent a couple hours searching for an answer to my question. I hate to ask (because I'm sure it's already been answered), but I can't find the answer, so here goes. #1. I'm attempting to set the timing on my '73 F engine. My flywheel has the metal ball, but no other timing marks. I...

SoCal Sensors, Oil Pan, Pulleys, AC brackets, Water pump, Starter, Oil level sensor, valve cover, wiring loom, alternator, distributor, injectors, exhaust manifolds, intake, EGR, etc etc. all from 1FZE engines. Also available are ECUs, please specify year and wire harness. Please include your...

Got a 1967 FJ40 with an F block and 2F head and long tube headers...I recently had a shop do a head gasket replacement, prior to the head gasket going bad the valves were pretty quite..Afterwards I have valve ticking and one that tends to constantly loosen..Oil gets to the head..Im running...

Got a 1967 FJ40 with an F block and 2F head and long tube headers...I recently had a shop do a head gasket replacement, prior to the head gasket going bad the valves were pretty quite..Afterwards I have valve ticking and one that tends to constantly loosen..Oil gets to the head..Im running...

I know our wheels don't have much of a flat area to install them, but just curious if anyone here tried it anyways.

I have a 67 FJ40 with an F block and 2F head...Recently had head done and have had help adjusting valves...I can't find TDC mark on fly wheel is there anyway to adjust them without the mark...The only thing on flywheel I can find is a square and the needle and notch but no BB or or line..

i have an 89 4runner im restoring and i am having an issue trying to get a mechanic to adjust the valves local to NYC. its currently sitting at a friends house in LI getting some work done. let me know thanks

Selling a set of 6 inlet and 6 outlet VALVES. $ 120 + shipping Also available on request. KolbenSchmidt Pistons + Rings. These are for the F engine. For 2F also available $650 (6) + shipping

This group buy has been canceled due to lack of interest. Talk about these replacement valve stems has been making its way around ever since their successful crowd funded launch. Finally they are available to everyone and I've been able to negotiate a group buy discount from them for our...