shifter

Hoping someone can post a picture of the wiring coming out of this connector. I had a short and fried the wires so I can’t tell how to wire it back correctly. Also looking for this connector (male and female) if anyone has one. If not I’ll bypass the plug. Thanks!

I’m looking for a complete gray shifter for my auto conversion., and the floor plate. Also interested in a brake pedal assembly from a FJ62. I’d take brown if I can’t find a blue one Let me know if you have a setup available

Gday everyone. I have an LS3-swapped 96 GXL where the previous owner had installed himself. He did his best to use the stock auto shifter but I'm not able to shift below D (into 2 and L). As a newb to car mechanics I've spent many hours today searching the forums (V8 swapped thread in...

I conquered the front DS clearance issue, but have been struggling with getting the TC shifter to function. I have built several types of mounts off of the trans for the factory shifter, but just can't seem to get the H-N-L portion to function appropriately. For those who have tackled this, do...

Looking for an early model transfer case shifter retainer and shaft (PN: 36344-60021), the pic should show exactly what I am looking for, it's needed for the LT swap kit I have from @torfab Any questions please let me know. Thanks.

Hello!! I converted my 3 on the tree to a floor shift in my teens. Now nostalgia is telling me to go back to that 3 on the tree. My dumbass did not save the parts from back then so I’m looking for a lead on where to find the parts to do it? Thanks!!!

A packrat got into my resto-mod project and chewed holes in my transmission & t-case shifter boots. FYI, I am using an FJ60 bezel to give me room for the 4-speed under my 3-speed transmission tunnel. Please let know if you have a replacement set for me. Thanks!

So i've had this problem a few times now. In the beginning i didn't exactly know what was causing it. It's a 2011 GX with around 150K miles. I've noticed after i return from long work trips, it seems like the shifter is a bit "sticky". I thought it was just because the rental cars i usually...

Does anybody have pictures of what they did so the shifter isn't up against the passenger seat?

Complete 3 speed floor shifter and TCase shifter & linkage. $75 obo + shipping. Thanks Ernie

Have nice boots for the parking brake and transfer case shifter removed from a 96 80 series. Great shape, $35 for the PK boot and $35 for the transfer boot. Buyer pays shipping. Best to email me shmukter@pa.metrocast.net

Thought I’d share since I know lots of us have worn leather on the shifter handle. Took a gamble and ordered a replacement cover from AliExpress for ~$20. 100% satisfied with the results. Just don’t be a dummy like me and attempt to take apart the O/D switch.. just de-pin the connector under the...

Does anyone have either a template or good pictures of where the stock holes are supposed to be in the transmission cover for a 3 speed with manual transfer case? Mine had a vacuum actuated transfer case originally and someone just cut one big hole in the cover. I would like to weld up the...

What are some shifter boot ideas after modifying body/trans cover for small block chevy on a 1979 FJ40. Downey, back in the day and Advance recommends moving drivetrain forward for correct engine placement. This puts the shifter boots at the bend between firewall and trans cover, under the...

Shifter for sale. P,R,N,D,3,2,1. Usually wanted for LS swaps. $125 + shipping.

Does anyone make replacement ends for the shift linkage? Thanks

Looking for a good condition shifter assembly to combine with my current shifter. Ideally the grey but can likely make brown work. The important condition pieces to me are the plastic PRNDL etc being clear and uncracked. And the little pieces that move with the shifter as it goes forward and...

Air Filter Lid from 1997: $60 + shipping Shifter from 1991 Land Cruiser $125. Shipping is available.

Left hand drive 80 series manual shifter console. SOLD

I'm sure somewhere in this forum someone has mentioned this before. My 80 has too much slack in the shifter or either underneath. It causes it even on rare occasions to slip into neutral if I accelerate too much without paying attention to it. I have replaced my motor mounts and I believe my...