parts

Looking for the floor pan sheet metal that goes under the gas tank. Also looking for windshield wiper motor brass tube, windshield wiper arms, dash board metal from the passenger side and seatbelts to start. Located in NW Louisiana

One clip. 1 clip. Sólo uno. Seulement un. 唯一. 只有一個. Einziger. Ain’t but one. 60.00 plus shipping.

100.00 plus shipping for the lot. 3 point set on right. Can’t get them to pull out. Perhaps I don’t have them in the right angle. 2 in center are for rear. Two on left are for bucket seats?

Cool Chrome Kick Vents. Okay…maybe not so cool. 40.00 plus shipping.

Hey there NC folks. I am in a tough situation and need recommendations for how I can get my 1997 LX450 repaired (after 9 months of waiting) - either by having it towed to a different body shop or ideas for how to help my shop get what it needs. I'll share background below. Let me start by...

Bought this near new from Toyota h55f from an employee at Mudraks who used it for 8k miles and then popped a cummins/nv4500 in his 60. Pulled this one out. George of Valley Hybrids rebuilt another split case i had and upgraded the case with all the bells n whistles/McNamera gear etc. and...

PLEASE READ the below listing of parts we have for sale. If it isn’t listed, I don’t have it so if you ask that means you didn’t read what I have listed for sale. Need to move/unload a fairly big pile of parts from an abandoned 105 build. Project was canceled which is why we need to sell these...

I have a few FJ40 parts off of a 75'. Steering wheel, and center cap $175 obo plus shipping Horn button and wiring $30 plus shipping Tail light housings...SOLD Fuel door $ 15 plus shipping Message me for prices

I have a 1995-1997 80 series I’m parting out. The engine has 305k on it. The wiring harness was cut before I purchased the truck so the condition of the engine is unknown. This would make for a good rebuild motor and accessories. Entire 1fzfe long block with all accessories and ECU $750 OBO...

Hi there, Wanting to have a fun project and convert a 460 into 150 and was wondering if anyone has recommendations on importing Aussie parts to the USA and the process? Specifically TJM or TWD bumpers. Thanks

I have 96-04 Tacoma trucks for parts. Good running low mileage 90k miles engine and tran. 3.4 engine , auto trans , 4x4, 4d cab let me know what parts do you need. thanks

I’m done with any aftermarket parts. Even something as simple as a drive belt, it needs to be OEM. The Dayco that a mechanic used as my daughter is in college and I couldn’t do it myself as she’s several hours away, lasted less than 2 years. Put a new OEM one on today and the noise went away...

2000 series 100 LC with 308K and I have owned the vehicle since '02. Unfortunately, I did not identify a blown water pump and the engine seized. Significant mechanical additions/changes were made at the 248K mi point (2016). This would be an EXCELLENT vehicle for an engine replacement but I...

Looking for a pair of FJ62 Parking Lamps. Don't care about the lens. Just want the assembly and the wiring, mostly just the wiring actually. Please DM me if you have something available.

Anyone got any bump stops and/or limit straps they want to sell ?

It’s been several years since I was in the Landcruiser world so I’m trying to get reoriented. I want to replace my ignition coils on my LC and want OEM bits. Short of using my local dealership, what are the best options for OE parts?

Used for a few hundred miles on my LX470 but too stiff for my setup. Buyer pays shipping. Only accepting Paypal or cash with local pickup in Tulsa, OK. $100

I can send pictures but I have a Safari Bumper, Temp Control unit (I have 2! ! is perfect and one has the temp slide broken but could be used for parts), Original Jack, Mid Seats OEM mat, Rear OEM mud flaps, Center shift console plastic in tan, Center temperature Bezel plastic with 12 volt plug...

I was cleaning out the garage and found some old parts I don't need. Cluster $30. This is definitely a cluster for parts. The MPH needle is gone. The harness and other parts could use some TLC. Crankshaft Pulley $75 $60 Press-on type. Needs a speedy sleeve. I'm pretty sure this one came off my...

I’m in the process of dismantle it my 93 that got tipped over last spring. I’m getting close to being ready to take body and frame to the scrap yard and figured I’d ask if anyone wants a solid, rust free 80 frame. I’m located in SW WA 25 miles NW of Portland Oregon. $200/offer If...