injection pump

1992 prado Need help with some torque specs on a 2lte diesel injection pump and rebuild kit. I am starting with the top o rings while on to see if it’s just that because that is what it looks like. Denso part number 096500-5010. I am new to diesels so any help would be great. Pic for attention.

I’m selling my backup Toyota 1PZ injection pump, Part Number 22100-18010. It has just returned from a fresh professional rebuild and is fully ready for installation. Photos of the pump and documentation showing the rebuild are available here: https://adobe.ly/3L0hhtC Price: $2,250 + shipping...

Hey brains trust! I recently got the mechanic to a leak on all six of the injector delivery lines. Previous to this, the 2H would run a bit rough on cold low idle (no smoke at all), but revving up with the hand throttle fixed this. Once she was warm all was good. Since fixing these leaks, it...

working on a 1981HJ47 with a 2H cracked oil cooler cover plate trying not to remove the front cover I searched and found an old thread from 2012 that said the gear doesn't need to be removed to remove the pump can I remove the pump from the pump retainer, 4 nuts? or better to remove the pump...

Used 2H injection pump and injectors. Good condition. Check out our other stuff! $1000

Hey guys i'm at a bit of a loss and just checking to see if anyone has any other ideas I could try before i send my injection pump or the whole car to a diesel mechanic. So i've owned the 1982 BJ42 (Australia) for about 8 years with absolutely no issues engine related. Engine is (was) super...

My '91 JDM HDJ81 recently developed a drip from the injector pump, which seems to cure itself once warmed up. I was planning to investigate the source, and temporarily reseal if appropriate, but then after a visit to the local Sam's Club I cut the ignition and she kept on running at very low...

Hi everyone. Is there anyone with 1pz engine for sale? Or maybe the 1 pz engine cylinder head with injection pump? Plz let me know willing to buy it?

Hello, My 100 series diesel has no power when I accelerate and makes loud noises. The injection pump wiring harness was tampered with by the previous owner. Toyota no longer manufactures this wiring harness. Do you know where I can find one? Thanks toyota reference: 82121-60850

Hi everybody. Thinking about importing JDM Land Cruiser HZJ77 to Seattle, US. It will have 200 k - 300 k kilometers. My previous (oversees) experience with not so young diesel JDMs tells me that some initial pump and nozzles will probably be required. So far I have made several phone calls to...

Toyota 2H Injection Pump and Injectors serviced/ready to fit. Injection Pump : sold Injectors : sold

I have a 94 4runner 3.0 5 speed 4wd and have replaced a few 3.0s over the years and recently bought a rotted out 94 surf with a 1kzte in it and I’m planning on swapping the motor over in the next few weeks. My only questions are: 1. Are the 3.0 motor frame mounts the same as a 1kz? 2. Can I use...

Any thoughts on whether or not this would work for a 2lt pump? Apparently my pump doesn't have the hole tapped from the factory. None of the 2lt engines in the US came with a tach so I guess that's why there's not a hole pre tapped, but I know basically every other country had the NA 2ls with...

Hi, Second attempt at understanding what is going on here. I'd like to hear toughts as to how it is possible for the timing marks on the crankshaft and the injection pump pulleys to not match up at TDC yet the engine still run? Crankshaft pulley offset? Injection pump pulley offset? Timing...

Hi Guys... I had a fuel issue on my cruiser... I had just completed a 4000km road trip... and then another 1100km road trip on the vehicle with no issues when 7 days later it was struggling to start, and eventually would start only after hand priming or push starting on a hill. This proceeded...

Have a 13BT with an upgraded CT26 w/ Garrett 60-1 wheel. Biggest issue is it’s slow to boost. Not intercooled yet not sure if that would help, but I started to play with the timing some today but I’m totally new to messing with Injection Pump timing. I moved the whole pump about a 1mm advanced...

So i put my engine back together after throwing a ton of new parts at it but as. i was reading through the repair manual i found that this knock pin goes in this area but i never put it back and dont even remember it being there, runs beautifully but should i be worried? 😞

Hi, Looking for a 1PZ injection pump. Preferably in good working order. Thanks!

Hi Mudders, I'm switching from an IP that's equipped with an HAC, to one that's not. One difference is the throttle control arm that attached to the top of the IP and also provides the fuel control limit via a metal tab. Unfortunately the lever from the non HAC pump is missing and I need a...