harness

99 UZ100 After extensive squirrel damage to under hood harness and subsequent removal and re installation of the OEM spec re manufactured harness the truck runs, ABS system (damaged by shorted wires) works as intended, front AC blows cold and runs correctly, the only issues presenting are rear...

Hi Guys I am sick of the lousy sealed beams on my FJ60. I am searching for one of SLCFJ62's headlight harnesses to fit H1/H4 an FJ60. He has unfortunately stopped making them and I can't seem to find a schematic or parts list anywhere online. So if anyone has a spare harness or a used one...

Hi Guys I am sick of the lousy sealed beams on my FJ60. I am searching for one of SLCFJ62's headlight harnesses to fit H1/H4 an FJ60. He has unfortunately stopped making them and I can't seem to find a schematic or parts list anywhere online. So if anyone has a spare harness or a used one...

Quick question on my '76 FJ40 ignition upgrade - I installed the FJ60 coil and igniter in the same location as the FJ40 parts and figured out/reconnected all of the wiring except for the two wires to the distributor. The wires are about 6 inches too short. Is there anything special about these...

77 complete harness

anyone know where I can get a already fabricated harness for a 3.0 to 3.4 engine swap harness? I heard someone might prewire them on hand? Thanks

I'm in the process of replacing my entire wiring harness from the computer out to the block plugs/sensors. I did a search and didn't find a lot of information on this swap, or perhaps i missed it. Flipping through my FSM i haven't been able to locate a complete diagram of the wiring...

I am installing a new wiring harness in my 71 FJ40. I need to know if I can install a fuse able link in-between the voltage regulator and the fuse box. The + feed comes from the voltage regulator directly into the fuse box (different from the original factory harness). I had an issue where my...

I have a full wiring harness off a 1986 FJ60. $175 plus $25 to ship anywhere in the lower 48 via UPS Ground PM me for more info Quite a few pics here

I have a brand new wiring harness that I no longer am going to use. I purchased it for an engine swap project and the guy backed out. It is a stand alone harness for a Gen IV/ 6L80E or 6L90E trans. This will fit any of the 2007 to current truck engines with or without active fuel managment and...

I installed a brake controller and a 7 pin (hopkins) female for the purpose of towing an airstream. It's all hooked up, but not communicating with the trailer, confirmed with test light/om meter. My 08 has the hitch, and female wiring adapters for the 7 pin harness, but is it possible it's not...

I'd like to put some additional exterior lighting on this thing. I'd prefer to use whatever existing wiring harness provisions exist, whatever slot exists in the fuse panel, and a factory switch put into a blank on my dash. Where do I start digging?

I searched a bit. I couldn't find where people are mounting these. IF ballast can set in the space behind the side marker, in the fender, where is a good spot for the relays? Thanks for any help Jerry

this is the complete front and rear wiring harness. Lots of the end connectors need to be replaced. It's in good condition overall. After having to replace sections of mine recently I understand the need for a complete harness so I took the time to remove it. $120 plus ship

G'day, long time lurker, new member and ham. Looked through through forums, and didn't find any mention on whether 'tis a good idea to get power for a mobile rig from the 7-way round trailer harness (100 series) for temporary installations. That way I can move the radio from my truck to my...

I have a complete '82 40 wiring harness in good shape. $200

just removed it is a complete harness from the front to the disconnect in the back driver side. This does not have any of the back connections at this time. Taking this out I cut one wire to the antenna and that's it Great if you need any spare factory parts. $85 shipped

I have a 5.0 V8 EFI from a 1993 Thunderbird with complete running wiring harness and computer. It also comes with a NP435. Includes alternator, fan, complete air intake. Everything you need to plug and play into your truck. Mileage is unknown on the engine and transmission. It starts up and...

I found a issue with my 100 last night. There is a hole worn in the drivers side wiring harness back where the previous owner had installed an inverter.(in the Subwoofer Space) I am really surprised I haven't seen any issues up to now. Only discovered it because I was adding some stuff and...

Intact and good condition from my 76 FJ40. I'm building a crawler and most everything has/is coming out. I see one wire repair with a crimp fitting and one single wire cut off, both pictured below. $250