Decided the battleship gray original paint on the shifter plate between front seats needs a refresh. Went mat black and with a mat clear coat. Multiple layers and a week drying time.
Dealer for those piss ant replacement light bulbs to switches and Drive shift. Clueless why Emergency Flasher...
Below is a picture of two identical glow plug relays. On the left is a brand new (actually 30 year-old NOS) version and on the right is a relay from my BJ60. The car has well over half a million kms and is an indirect-injection diesel, so glow plugs will have been used for every cold start...
I have a 1989 hj75 2h and I’m trying to order some new glowplugs but every site only has ip to 1988 and I’m not sure why, and anybody know the voltage that my glowplugs would run because there is heaps of differnt options! Cheers
hi guys looks like there are more choices for glow plugs any advances to running the CERAMIC Type?
OEM part number 19850-64031
DENSO part number: DG-649
BOSCH GLOW PLUG (NOT-CERAMIC)
Bosch Glow Plug - GPT-220
BOSCH GLOW PLUG (CERAMIC)
Bosch Glow Plug - 0250202095
NGK Glow Plug - Y744M
Hi guys, does anyone have any ideas what could be causing this on my HJ 45 diesel slow poke 3.6lt ……when it is cold first thing in the morning when I glow it for 20 seconds Then start then it runs for about 10 seconds then just stops, turn the key again runs for another 10 then stops, third...
Greetings all.
The glow plug light on the dash doesnt turn off (KZN 130 1995)
I have replaced the glow plug timer and when checking with a multimeter, there is no voltage across the glow plugs... but the light stays on.
Any advice on how to troubleshoot where the problem is?
cheers.
The dreaded super glow thread...
I've actually been running a Ford starter relay directly to my rail, it's been fine, but id like the simplicity of just turning they key and letting the computer tell me what to do, plus I see some work on a modernized computer so I want to get my wiring back to...
After enduring too much trouble with my original superglow timer which frequently did not operate correctly I decided to use my electrical engineering knowledge to make a timer replacement.
This board is based on an ATMEGA328P for the logic part.
Current features support:
- Water temperature...
Hi all, in all schemes I find the wiring like this (I added wire colors)
My car is 4 cylinder but that should make any difference, however, the original connection in my car is like this:
Any ideas why it is different and what is the purpose to change like this? It is weird because the thick...
Yesterday I was having some issues starting my 60. Disconnected the terminals and cleaned up all the connections I could. While doing so the double eyelet for the fusible link feel apart from corrosion. While messing around with that I noticed that the large black wire (small black FL wire)...
2 glow timers (pre-heat timers)
1 is for hdj80/81, the other is for hzj80/81. The part numbers are different although they may be the same exact part. $250 each + shipping
Hi All,
I have just found this forum after asking Mr Google about glow plug probs.
I have a HJ47 which is giving grief in the cold start dept. After reading through several threads on here I am thinking of converting to a Wilson Switch and running dual element 11v plugs. I tried to chase up a...
I am trying to troubleshoot my non functioning glow plug system on my Nov 1985 24v HJ60. The previous owner put in a Wilson switch, but it never worked as long as I have had the truck. It stays warm year around here in Hawaii, so I believe it has been able to start up without a functioning glow...
Hi there,
I am new to Toyota and acutally dont have a Landcruiser. My current toy is a 1993 Toyota Coaster, which at that time was manufactured with a 1HZ engine without turbo and a 24 volt system. I hope there a some people here who have experience with this engine.
My current problem is the...