gear

I desperately need to order a shakey mirror fix for my new-to-me LX450. And while I was at it, I was thinking of ordering a set (or two) of his "seat gear cap guards". But I didn't know if they are interchangeable side to side, and I really need two passenger sides at the moment. And...

Brand new, never installed. $100 shipped (CONUS). Fits the US spec 100 Series dash very well. Defrost works fine, but there is no cutout for the light sensor. According to the Escape Gear website, the cover does not interfere with the passenger side airbag. These are really well made with three...

Howdy!!! Does anyone have the measurements for inside the Alu-Cab THOR conversion? I am talking the measurements of the inside of the mounting area for the Thor. Alternately, the measurement of the 76 right where the Thor conversion connects to the roof. Reason: I am making a box for my pickup...

So I have a GCC spec 1FZ-F 80 with a H151f and K194 lockers (in case any of these details are relevant to the question, hehe). I have to replace the clutch release bearing since I have developed crickets in the transmission, and I am wondering whether this is the time to upgrade the 5th gear -...

Getting my 40 ready for her maiden (to me) voyage, and was checking my driveline fluids when I came across this interesting sight. I guess my question is, when replacing the mustard fluid in the transmission, is it best to stick with the OEM Yellow Mustard? Has anyone had problems with honey...

Tuffstuff alpha 4 rtt Chinese happy sometimes diesel heater... Okanagan BC area 5500ft Elevation

I’ve had this happen in the past but can’t remember what it was? Just replaced the oil pan gasket and front seal. Thanks, Mike

I tried going in deep enough to replace my water pump preventively. But I got stuck early as I just could not get this stupid can gear off. It’s like it’s welded on. I found a puller that fits at a local shop but the teeth on it just bend. I’m not sure more force is really going to help preserve...

$385 OBO Text me 303-416- SIX NINE 8 1 Located in 91723 I need something bigger for my work. This was only used a few times. Charges to 100% no problem Come with an AC cord 720w capacity More info https://us.ecoflow.com/products/river-pro-portable-power-station?variant=40558475378761

Looking to obtain a VIN from a new 2022/2023 Prado 150 VX Matte Black edition. Really just need it for parts verification. None of the overseas sites post vins like they do here. GCC because left hand drive and can make sure headlight part #are correct for use here.

Ok, so it’s in every other section so why not here? Thought I would give it a go. If anything the thread can just die out. Feel free to post up what you did to your bike this weekend! Adding link to a forum that regularly posts deals for those replacement parts...

Hi all, New to the forum but long time reader. Afrer many years of suffering (JK), I'm finally in the position of getting a JDM 7 series. Been looking at HZJ70s on Japanese imporers sittes, but would rather go with one that other fellow members have had good experience with. I looked all over...

This is for two gear sets, F/R. Put the Rear on the front and have fresh gears in the rear. Great condition, around 8000 miles on the rear, less than 1000 on the front. Shipping ok. Yukon Gear & Axle high-performance ring and pinion gear sets are the benchmark of quality in the automotive gear...

1985 hj75 troopy, Oz, manual h55f. Not sure if I should post in 60's section as most 70's posts are for newer than what I have. Rebuilding h55f transfer. Have watched both otram and George's videos also referring to toyota manual and amayama schematic. Both Otram's and Georges videos are...

I have the 1240D with built in mppt controller (solar functionality is unused) and a Victron MPPT 100/20 connected to a 180w fixed solar panel. The redarc and victron circuits operate independently. Question : if I want to add a portable solar array ( I heard good things about the Bluetti...

3 no name 1.25" spacers $75 shipped. 2 by 2" trail gear spacers. $100 shipped

Debating pretty hard on what to get. Don't know what other options are out there. Anyone have any of these? Bison Gear Molle Panels at $112.50 each (sale ending less than a day) + 89 dollars in shipping = $314 including tax...

I have a 1993 HDJ81 Imported from Japan with a 1HDT 4.2L turbo diesel. Running 33 inch tires on the 16 inch wheels. Axle gear ratio I believe is 4.11. Thinking about running 4.88 or 5.13s to help with the turbo lag that is present from a dead stop to acceleration. Seems like the turbo kicks in...

Spot the risk, anyone? Good thing it didn't get much use. But at least it was well lubed 😂

1980 FJ40, 4 on the floor - I get crazy high amounts of vibration at the high end of 3rd gear and into the start of the 4th - once I get wide open into 4th it clears out. This has been an issue for a while but it seems like it's getting worse and shaking everything inside the truck really...