G’day
Broke my R&P a couple weeks ago, pulled my axle shafts and I’m currently rebuilding my front diff but when I pulled my drivers side shaft I found this metal “oil retainer” (I’m calling it that now, but I don’t know what it actually is) lopsided inside the axle housing behind (closer to...
$75 for the Pair of rear bumper corners to fit ‘91-‘97 FJ80 and FZJ80 models. Used but in good condition. A few scuffs. Sorry guys, but I’ll only sell them as a pair. Moving soon and need the cash. If you wish me to arrange shipping, then you agree to pay the exact cost of shipping in...
G’day guys
When I bought my 1994 1fz-fe 80 series it had been LPG converted. What I mean by that is the original auxiliary petrol tank had been ripped off and an LPG tank was fitted with all the parts that make the car run on both petrol and LPG.
I know this was a common thing to do back in...
Selling my 1996 Land Cruiser, $20K. 227K miles. Colorado truck it's whole life until September of this year. I am selling because it was a nostalgia buy and I truly don't have space or time to really get it to the point that I would replace my 200 with it.
My plan when I purchased was to turn...
Hey guys got an issue with my cruiser sometimes firing right up and sometimes I’ll turn the key and nothing happens . Am I looking at a faulty efi relay or fuse . Possibly neutral safety switch issue? Thanks in advance .
Finally decided to sell. Again. For the 3rd time. Each time couldn't bring myself to do it. Just no more time to use/wrench with small kiddo and crazy work.
Located in Bend, OR so really just posting here on the off-chance someone has contacts in Bend that may be interested. Craigslist...
Started My FJ48 Build about 6 Months ago and wanted to start a thread for inspiration and advice. This is my first time posting to IH8MUD but have been enjoying posts off this website for years! Basically I had a Rusted out FJ40 on the farm and found a 80 series at the neighbours that did not...
Selling a 1FZ out of a 96 LX450. Had about 220k, then Blew a head gasket. Had head inspected by a machine shop and cleaned and machined accordingly. 25 thou was taken off and she’s ready to run again. Bottom end should be good to go too, didn’t knock or anything, but I could bang the pistons...
LAND CRUISER AND TOYOTA ORNAMENTS
Variety of grill designs for various Toyota models perfect for the Christmas tree!
Check them all out here:
Ornaments | Lower 48 Outfitters - https://lower48outfitters.com/products/accessories/ornaments/
Getting my 80 restored and have a brand new short block going in. I am looking to sell the original short block that came out of the truck.
Block, pistons, rods, bearings ect. No oil pans or pickups. 260k+ miles. Came out due to head gasket failure. Rings might be worn some, but no other...
Hi there, my JDM 80 series came with authentic Red Recaro Bucket seats on sliding rails. I'm looking to do a straight trade for a pair of factory Alcantara heated seats out of an 80 series.
Cheerio
Hi there, my JDM 80 series came with authentic Red Recaro Bucket seats on sliding rails. I'm looking to do a straight trade for a pair of factory Alcantara heated seats out of an 80 series.
Cheerio
Question for anyone who has ordered from L seat before. I’m looking to get a set of new seat covers and trying to figure out which color matches OEM on a 1995 landcruiser. I think it’s bisque but not sure, any input in appreciated.
Hello all,
I have two Audi S4 seats along with power wire harnesses and seat heater wire harnesses. The seat heater wire harnesses were ordered from Germany and are plug and play.
I bought these seats last year for but I've decided to go in a different direction. I fabbed up a seat brackets...
Thanks to everyone that talked me off the ledge about 3 weeks ago, and kept me from selling my 80. If you remember, I got screwed by a local shop and the project was waaay over due and I was running out of options. I had offers from y'all from Florida, to Texas to send my rig down and get it...