fj80

Bearing is spinning on mine. Looking for a good condition replacement. Thx 770 298 7668 Greg

Just going to use these to plug the old holes on my exhaust when I move the sensors up to the pair valves old location. Looking for cheap! I'm in Portland, OR Will pay shipping. Thanks!

SoCal These are original sun visors that were selected for being in good condition, no tears or splitting, and not flopping down. ONE ONLY: Light brown Passenger Side ONE ONLY: Light grey Driver side. No rips or tears. $45 each + shipping at cost. Shipping Estimate is $20.00 as shipping...

SoCal 3 pieces available, good on both sides, not brittle, no cracking or issues. I am sorry to not have all 4 pieces, but as you all know, they break easy once they get brittle. Paypal OK. All 3 pieces including shipping $100.00, Each piece $35. shipping is $12.75 for 1 - 3 pieces...

Hi I am looking for an FSM the 1992 FJ80 variety. Please PM me if you have one available. Thanks.

Alright so who can tell me what I am missing. Went to start the truck at lunch and it wouldn't start here is what I have. CEL is illuminated No click no crank I am able to start jumping the terminals on the starter with the key in on position I am able to move shifter from Park into gear...

Hey everyone, I've been lurking here for a bit, just picked up my first land cruiser in January. I've been tinkering with it since I got it. Right now it has a cheapo roof basket mounted to the factory load bars. But I found an original Con-Ferr rack for a great price, and plan on going that...

I have two grab bars: 1) Brown FJ60 bar, complete with mounting gaskets/pads and screws. $100 2)Grey FJ80 (early years, pre95), complete with washers. $70

I'm working through a Roger Brown 1' lift and found my front frame bolts seized to the Front Body mounts. So much for the bolt sliding out. I'm looking for a pair of Front Body Mounts. Pictured is one pulled and the location of the other. They look very similar to the front mounts on the...

So has anyone had the experience of towing a decent size enclosed trailer with and FJ80 vs a FJ100? I'm considering the supercharger option for the 80, to tow a 7x16ft enclosed trailer, but for the cost and limited supply seems like selling it and getting a 100 w/4.7 would be about the same...

Not mine. Seems legit - current owner has already put a bit of work into it. A bit expensive but has a lot of things I'd want to do anyways. Thoughts? 94 Land Cruiser w/ E-lockers , lifted

I have not been able to use my hand break for quite some time. I recently purchased a Raybestos Brake Cable (BC 94525) and installed it. The cable appears to be too long. Has anyone had any experience with the raybestos product and can tell me if they are crap or did I just get a bad cable? Thanks,

Free Parts (with purchase of any of my used parts): All prices do not include shipping from Irvine, CA 92604. For Free with purchase: 3rd Member (pick up only, spline on pinion and flange no good) IMG_20170220_171129.jpg Aux rear heater lines (there is a kink in one of them) (Pickup only)...

Looking for stock fj80 front springs. Let me know if you have a pair. Thanks, Blaise

What the title says. Will buy either just a birfield with the lock ring or the entire assembly w/ axle shaft (will pay fair shipping). Just to be clear, I need the passenger side, non-ABS birfield. Thanks!

I have a 92 fj80 with slow leaks in the front and rear diffs. I was just wondering if I should use a gasket or just RTV? I read about people using "Right Stuff" on pirate, but I have never heard of it before. Also the truck has lockers front and rear. The rear acts like an auto locker and I'm...

Looking for an old worn out pair of FJ80 TRE's. I am planning on welding in some bungs into DOM tubing and want to use these as a sacrificial piece. Thanks Steve

Hey guys - Just listing my cruiser for sale as i am going to need the space for summer. It's originally from Texas, lived in PA then came to New York and has only been here from what i can tell a couple of years. i bought the truck because it is rust free. body / frame / tailgate / door sills...

So I decided to dig into the visor issue once and for all. I made a slit in the fabric along the seam in the area where the shafts enters and plan to rubber cement or find some fairly cosmetic acceptable fix in the end, and find a real fix for these. Once in the visor there is a clip that can...

I'm looking for any specialized mechanics for a '97 variety Landcruiser. Thanks!