Howdy,
Maybe I'm just not putting the right keywords together but I wasn't able to find much of anything on this topic in here.
I've got a 2000 LX 470, for which I'm looking to make my own armor. I'll leave the #1 cover for now because of the complexity of the contours, but given that I...
Been looking into drawers since about a week after I bought my LX. Like a lot of the manufactured solutions out there but had a couple specific needs in mind and wanted to turn it into a quick little project. Just sharing this here as a means to document this for myself, and so that someone down...
Hey guys, i see the same questions get asked all the time on heaps of different forums regarding how many kits did they use, whats the process, pros vs cons etc etc
So when i recently did a full respray of Raptor on the old girl decided to film a little bit of the whole process to try and help...
Hey guys hope everyone's well
I've seen a bit of discussion on beds inside their wagons as appose to swag or tent. Here are my thoughts on the matter, the pros and cons and how I made mine for roughly 30$. I love mine and provide a bit of info if your thinking of doing it yourself.
Hey guys,
I unfortunately don’t drive a LC but I do drive a 4runner (2003 sr5 V8 118k) and I was hoping one of you could meet up with me and help me diagnose/fix an issue my truck just started having.
My rear passenger side brake is making an awful grinding noise. I’m hoping its not the...
Ok heres the plan, I cuurently(no pun intended) have 170AH worth of odyssey extremmes under the hood a 70AH starter battery and a 100AH house/auxilary both fed off a 150amp seqoia alternator TO A NATIONAL LUNA dual battery setup I installed with battery the house battery runs to a bussman...
Well, at just over 180k my steering rack is starting to leak pretty heavily. I'm going to do the lift-engine method and replace it.
Anything else I should consider checking/replacing "while I'm in there"?
Plan:
New OEM steering rack
OEM steering rack bushing
555 Outer tie rods
I've got an air leak somewhere and don't feel like band aiding the air ride system, so I have my order on the way for the conversion. I need to do it this weekend, and it seems like all the manufactured kits are 2-3 week run time before I could get them, so I have decided to make my own.
I...
Hey All,
I just bought a 2006 Land Cruiser with about 110K miles on it. The maintenance records were pretty good with no major issues as far as I saw. I deleted the ACH myself and replaced with 1.5" OME medium kit, new 33" Goodyear wrangler Trailrunners, brake pads, rotors. I have a couple...
I've had a few 80 series, and one hundie Lexus before, and we just found ourselves with another hundy. A 99 with 215k, that spent most of it's life as a mall crawler in California as evidenced by the ht tires, wedding ring damage on the steering wheel, and the cleanest undercarriage I have ever...
Hey gents,
First post on here, did a search but couldn’t find anything to help so please excuse me if the helps here and I didn’t find it.
Recently purchased my first LC 100 series (224k miles) and love it so far. Did the timing belt/water pump and now I need to figure out the lights on the...
It took a couple of months of being on the waiting list, but they finally came this Friday. This is absolutely a DIY job - but it wasn't without challenges. Also, be warned: this is dirty job. My truck had probably 3-4 pounds of mud underneath. I can still taste dirt.
My hope is that this...
I wanted a set of bead locks for my bush truck but didn't want to spend too much money.
I bought 4 second hand 15x8 steel rims.
Instead of buying a weld on bead lock kit i went to an engineering shop and got 8 rings water jet cut out of 6mm mild steel sheet
I drilled the holes myself to keep...
Hey guys!
I'm in the process of building my own roof rack for my HJ60, as classic looking racks aren't really available in Germany, and shipping from the states would be ridiculously expensive! I already resorted to the Gamiviti Feet, since I like their design a lot, and again couldn't find...
Hey everyone,
I had Toyota Atlanta order an OEM Engine Air Filter as Lexus of Atlanta said it was extremely dirty. I see that it's the circular kind etc. and note clamps on it etc. Is it hard to replace as a DIY ?
Any advice or pictures or previous threads please? Will get the part in on...
Saturday, I spent the day swapping out my saggy, worn out, 200k, OEM springs on my LX450 with OME 861/862 stock-height springs.
The springs were labeled A and B, as I had read they would be on Slee - OME Suspension Installation (Toyota 80 Series Land Cruiser) and many other forum posts. I knew...
Hi all. New to the forum. Just bought my first Land Cruiser the other week.
Does anyone know how to remove the rear tailgate from the car? I haven't been able to find anything other than the tailgate lid install for extra storage. It looks like there is a torsional spring that could cause...
Hi everyone,
I've seen a few different posts on here for random interior lights/headlight/taillight/cruise control issues so I figured I'd post here to get all the answers on one post.
Issue #1: Cruise Control immediately cancels when turning ON blinker (left-blinker, in my case)
Issue...
$$$SOLD$$$$$$ cant use it for what I intended 425 tyd CONUS comes with case anderson plg welder extra consumabes coil and clamps.
SOLD ext me Ill send pics. price is frim...