cylinder

So, I think my brake cylinder is shot. I mean its clearly shot. A few days ago I replaced my front brake shoes and adjusted the brakes all around. The old ones were installed backwards, and one was chipped. The cylinders are also reversed, but I have just been adjusting them in reverse...

i need a new clutch master cylinder i have a 1972 fj40 and need to know if a master cylinder from a 1976 to 1980 will work thanks

This was barely used in my '71 until I figured out it was the wrong year for my truck... whoops. Pretty much like new. $120 + shipping from Los Angeles EDIT: PRICE CHANGE: $100 shipped

I beleve this all of 1976. It's ugly, but all worked when removed. $75 plus ride from 97070

looking for a master cylinder cap with wire and connector only for a fj80 shipped to 85249

I heard these things are umobtanium these days. Mine needs to be rebuilt- but it only had 68k miles on it :). I hate to toss something in the scrap pile that someone else is searching for. Trade it for a 6 pack of Pacifico. Located in Scotts Valley CA

While doing a valve adjustment for a customer, on a 91 FJ80, I noticed a glimmer of green in the sun. After pressure testing and cleaning the suspected areas I found this. It is located between the exhaust valves for cylinder 2 and 3. There is also a smaller one in the same spot but between...

New, OEM Toyota dual reservoir master cylinder. Fits 9/75-7/80 FJ40/55. $175 plus shipping from IN.

I am in the middle of a total engine rebuild. I have the block stripped, and am ready to take the main components to the machine shop tomorrow to have everything checked out. I'm pretty sure I will need to bore the block, as there are some marks from the piston skirts in a couple cylinders. A...

Looking for a 2F Cylinder Head for an 84' FJ60. Please message me if you have one available.

Hey guys I have a 76 cruiser with the stock disks up front and drum rears. I discovered that my master cylinder was leaking a little and wanted to up grade to the 80 series master. I would also like to convert to rear disks in the future. I bought a 1994 80 series non ABS master. Should I...

I just replaced the master cylinder on my FJ62, and here is the master that I pulled off. Not stock. Anyone know what it is from?

I am about to put the cylinder head back on after a headgasket replacement. Bolt holes look clean and thread in without a lot of friction. I plan to use new OEM head bolts oiled per FSM. Reading on mud some say to chase the threads. FSM does not state to do this. I plan to run my bolts down each...

Evening everyone, Cross posted here to hopefully locate something. In need of a 3b cylinder head shipped to 93442 morro bay California. Or I can arrange pickup pretty much anywhere in California. Thanks everyone Cheers, -Joe Rawson JoeRawsonSLO@Comcast.Net Wanted - 3b cylinder head

In need of a 3b cylinder head shipped to 93442 morro bay California. Or I can arrange pickup pretty much anywhere in California. Thanks everyone Cheers, -Joe Rawson JoeRawsonSLO@Comcast.Net

Evening everyone, I recently came across a FJ60 with a 3B and H55F swapped into it. Motor wouldn't start and had very poor compression. After pulling off the head it appears to be cracked pretty badly. From my understanding all the pre cups are cracked along with that all 4 chambers have cracks...

Patient presented with "smoke" at startups, after changing to a new oil. Was using valvoline 10w30 switched to Valvoline Premium Blue 15w40. On pressurizing cylinder #2 to change valve stem seal, I observed bubbles in coolant reservoir. For a history, Engine has 161k miles, compression OK not...

I have a 78 FJ40 that has dome pistons. I am looking for a cylinder head. The one that I had on it was open chambered. Thank You, Rob

I'm sure it is out there somewhere but I can't find it and I am in a time crunch. I had to replace my brake booster on my 1995 FJ80 and during all the disconnection I have forgotten where everything goes. I have a black hose that appears to gush brake fluid if I lower it below the master...

I need a head for a 3F engine. Would love to know if anyone has one state side.