cap

Guys, is it possible/safe to only remove the white cap of my FJ40's hardtop? I need to re-do the headliner, and it seems like it would be much easier with the roof upside down on saw horses. I didn't know if there would be enough lateral stability for the windows without the white cap in...

Greetings! I’m in the process of replacing thermostat, water pump, coolant hoses, etc. The previous owner removed the heater and from reading on this forum I’m pretty sure he just rerouted the heater hose from A to B in the picture. My question is, can I just place a cap at A and B and remove...

I don't believe my gas cap is OEM, so it will be getting replaced. I have been considering for a while getting a locking fuel cap, but I'm worried about quality control issues and all other issues that might arise when purchasing aftermarket stuff. I'm leaning hard towards just getting an OEM...

Hi all, I have been hunting for what appears to be a discontinued item-- distributor cap for Jan 1980 CA FJ40 (with smog). Any suggestions where I might source greatly appreciated. Best, Ed

I bought this about 10 yrs ago for a FJ55 resto. I never ended up using it. Its still in its box. Cleaning out the shed and would be nice for someone to use it. 60$ and if you want to cover shipping, I will send it out to you. Lee

Went to check my fluids today and noticed the power steering reservoir cap was loose. Unscrewed it and saw a spring chilling in the hole of the reservoir. I assume my cap is falling apart? If so, I'll just go get a new one but want to make sure I'm not losing my mind first.

Hi all, I've seen other posts but mostly about 80 series or 100 series that we're resolved. I have a 2004 LX470 and after going to altitude (usually above 9000 ft from 4ish) with a full, or near full, tank I have gas coming from the gas fill door. I only notice it when I get out and don't...

Hi all I just did my rear main seal and followed @Poser ‘s method, which is taking the oil pan off along with the main bearing cap (#4). My engine is a ‘77 2F, and I have it off the vehicle on an engine stand. Overall it went very smoothly. When putting the main bearing cap back on, what is...

Brand new OEM Toyota washer fluid reservoir part # 855341021 (fits FZJ80) Reservoir brand new (cap used but good condition) - $70 shipped. This is a smaller bottle than FZJ80 US factory tank. Direct bolt in however - OEM Toyota quality.

1995 Land Cruiser - Looking for a left rear end cap if anyone has one in decent shape. '93 -'97 LandCruiser

I am getting ready to pull my block and want to make my life easier by pulling the condenser. Anyone have recommendations on how to cap the lines? The engine will probably be out a month or longer depending on how much work my block needs and life happens so I want to properly cap them from...

Looking for the cap that goes into the opening after armrest removal from a FJ Cruiser, preferably grey. It looks like a teardrop. Willing to buy 2. Part no. : 72848-35010-B0 Located in Canada. I am willing to pay for shipping and through PayPal GS only (I will cover the fee).

Hello, just bought a ‘04 LX470 and it is missing 1 of the wheel center caps w/ gold L. If anyone has one laying around or a full set of the ones w/ the silver L I will be happy to buy. Thanks in advance…

My gas cap key cylinder seems to have snapped, then some plastic things fell out of the side. I could just buy a new cap, but it seems like maybe the metal thing where the cap sticks in is bent. I'm not entirely sure. What should I do? What are my options? If y'all think I should replace...

I will be completing a 79 BJ40 & am looking for styles of pulley removal systems for topless operations. Constructed with removals in mind. Safety tip or suggestions are as always, greatly appreciated.

Looking for a Gas Tank for 1960 FJ25 or Early 40 . Dallas TX Thank You Robert

Hey Mud Looking for a visor/windsheild cap for a early/pre-65 corrugated hard top. Needs to fit on the type of windshield frame with the long rectangular vent under the glass. Stay Rad - TSH

Any recommendations for a good fiberglass repair place? The cap from my '73 is all there, but extremely weathered.

Hi I’m trying to assemble a new fiberglass cap and rain gutter… the rain gutter is nearly finished and ready to be riveted to the cap… how should I space out the rivets? There are a lot of them and I dont know where to drill the holes. Also how should I ensure that the bottom of the rivets won’t...

New distributer cap with 3 screws and regulator. For later model FJ40s.