I wanna raise my low beams up a little bit. From the picture attached I'm assuming bolt C is the one I need to adjust.
How the hell can I access that screw without having to take out the entire housing? it's very close to the metal mount behind it and just not seeing an obvious solution.
Hey folks, I'm working to adjust the valves on my 1HD-FT, and was wondering a few things. Hoping to get some advice from folks who have done this before. The backstory here is that I went to replace my valve cover gasket, and thought I'd adjust the valves while I was in there - but I'm quickly...
I’ve replaced my mystery OME springs (1.75-2”?) with heavy load linear Robinson springs (3”), this netted me about 1.5” lift.
After doing the alignment, my caster is a -1 degree. However, I DO have the OME caster correction kits installed when OME lift was installed by previous owner. From what...
Model : FJ45 1983 - stock
I noticed recently that I had alot of engine vibration, maybe low speed, and the exhaust fumes were excessive. There's no smoke. Thought it was time to re-adjust the carburetor using lean median method.
Set-up
- Digital tachometer connected to the coil
- Vacuum...
What is the best "Friction Point" or Pedal height to engage the clutch on "71 FJ40?
(And How do you adjust it?).
Was Plowing Snow, accidentally in High range for a bit, and got some smelling and burning.
Seems to still work OK but would like to double check it.
I installed OME 2865 coils a few months ago and cranked up my OEM torsion bars less than 1.5 inches and then had had it aligned. The steering became super light and I ended up with a shimmy in the steering wheel around 70mph. The shocks are new OEM, the UCA is original and I have not added a...
Hey folks.
I currently have two 80-Series that I drive regularly. They have very different turning radiuses. I initialy thought it was due to wheel offsets, however I swapped wheels around and the radius is still noticeably different.
Is there some sort of adjustment, or year-by-year change...
Hello,
I have a tried the AHC sensor lift method, and followed the videos and write ups on here. I did not gain any lift. My truck AHC system works with no issues. Just need help or advise with the AHC sensor lift please. Please advise. Thanks
Got a weird one for yall
Passenger seat adjustment controls -
Forward and back works fine, seat back tilt works fine, but the raise and lower for the seating surface don’t move. I took both side panels off to compare and the brown joysticks feel like they are locked into place, they don’t...
Finishing up my boost compensator install and came to the portion where I need to install the Throttle Position Sensor (TPS). The FSM states I need to supply 5v to terminals VC and E2.
My question; Whats the best way to supply 5v? Or is there a better method?
Hey I may as well try posting here. I recently purchased a 1981 C1500 with a propane conversion.
Its a 305 high compression with a high lift cam and a single plane Holley intake. It's running an Impco 425 mixer, Model L vaporizer, and a vacuum lock off.
I filled the tank at 64,593km
137km and...
Had my alternator replaced today and when I went to pick up my LX, the steering wheel was really really high forward. So much so that it was hitting the plastic lower shroud of the column. When I tried to adjust it, it telescopes in and out fine but when I went down it didn’t go very far down...
My oil pressure gauge needle in my BJ40 rests way below the 1st marker. I mean, it's bottomed-out. When the B engine cranks up the needle rises (significantly) to a position just past the 1st marker on the gauge. It would appear that the engine is producing good oil pressure, but not as...
Having some issues trying to get my heat to adjust from cold to hot and vice versa. If I pop the hood, i can open and close the valve manually to obtain heat or cold, so in the summer I close it and the winter I open it, so I know the valve isn't the problem. If i disconnect that cable at both...