2f

This wasn’t really in my immediate plans, but I happened upon a 2F near me and I’m going to set up a time to go look at it. Here are the details: 1985 2F with 244K miles Includes H42 transmission but not the transfer case Engine is still in the truck and the seller has a video of it running...

New 2f gaskets. $25 each +shipping - Timing cover gasket set - Oil pan gasket set - Lifter cover

Hello I recently purchased a 2f out of 1987 fj60 with newer carb and smog stuff. I also have a f carb from original engine 1970 that will probley need a rebuild. Should I D smog newer carb but also have figure out going from cable 1970 pedal to mechanical carb.

Guys, Need some help, been chasing an oil leak. I thought I had it by replacing the following: -Oil filter housing to block gasket -Fuel pump to block gasket At low speeds (up to 50mph) I have min. oil leak, almost not noticeable. But at fwy speeds, the oil amount that leaks is all over the...

Hey guys, Installed an EGT gauge on my rig as a precaution for tuning. Curious if anyone has done this on their fj60, and if they have an approximate reading that works for them. I installed my probe right beneath the header (which I'm sure changed the reading slightly) Happy New Year! Dan

I currently have a 74 FJ40 with a 2f engine and 75 carb. Can I use the original setup on the 74 which consists of the wire on the harness side coming through the firewall (attached picture) or do I have to use the 1975 setup? Any help would be greatly appreciated. Thanks

I am rebuilding my 1982 2F motor and I hit my crank journal with my piston connecting rod creating a small divet … ugh. Anyone have a crank with polished journals and standard size (not grounded)? I prefer not to pay for shipping due to the weight so something local in SoCal.

I have a Holley 350 2bbl w/chimney kit installed that was recently factory refurbished from Holley. It also comes with a 2F adapter and all hardware for the conversion. I bought it from a friend to run on my FJ40 when he pulled it off of his FJ40. It ran well and did well off road, but he went...

Hi, Who’s got them in stock ? I need 12. Thanks, Mike

Looking for good running f or 2f engine in North east area or farther if shipped

Hey I have a question for you guys that replaced the 2F FJ60 exhaust manifolds with a 3FE exhaust manifolds Did it change the drive ability around town on the freeway or increased or decrease the low end torque for 4 wheeling did it help with any more power or gas mileage?? Thanks I'm just...

What should the piston ring gap be for ring 1 and 2 for 0.040 oversize piston on a 1982 2F motor?

Howdy central Texas folks, Looks like my late 1986 2F head has a crack under an exhaust seat. So I am looking for a late 2F head that does not have cracks to complete my rebuild. The casting is 61040. Please tell me what you have. Thanks Ernie

Hey guys, installing my insulator plate. Thoughts on cleaning up this surface? Obviously it looks great, but just to prep for mounting. Dan

All, I've been fighting this hesitation since I got it back on the road after years of sitting, '96 was the last time it was registered. Symotoms: Hesitation when engine is colder, get less noticeable when warm, but still definitely there. Feels like someone has a tow strap hooked up and is...

Hello All, I have a 2F engine and 4 speed transmission from a 1985 FJ60 for sale. I will sell them separately or together. These came out of a truck with 180k miles on it. The transmission shifts nicely and is in nice shape. The engine runs well with good compression but burns a lot of oil...

Selling my other 2F, going to a diesel. This would make a pretty sweet setup to drop into an earlier year 40 and add power steering. This engine is out of a '79 that was used as a parts rig due to a high school auto shop butchering the rusty body. I got it running for the first time in about 20...

My 2f cylinder head is cracked, casting 61040. I am looking for one that is good to go. I don't care if it's ready to install, I just need one that's not cracked.

I am on St Simons Island w/ a '79 FJ that I have owned for 12 years. Engine just turned 100K, but due to oil leakage, I may need to look into engine work. Any references for shops in GA, SE SC or northern FL? Thanks in advance.

Currently have my intake and exhaust manifolds out to replace gaskets and hopefully improve a low vacuum condition on my 86 FJ60. Having trouble to find a machining shop that knows how to handle the assembly to clean it up and get the full surface flat. Mixed material between the exhaust and...