2f

So I actually have questions on both my trucks, as I've never been able to advance my timing beyond 7-10deg BTDC. However, I'm going to avoid questions on the properly running truck at the moment and concentrate on the FJ40 that just suddenly decided to not run right. Quick backstory, I've done...

2x 2F cores for sale. One was initially in an FJ40 and was pulled due to low compression in a cylinder. The head was found to have a crack (could be repairable) but the short block is fine. $750 for good short block with bad head. The other was from an FJ60, and was in my 60 for a couple...

Hi Mud, I havent been able to get a straight answer to this question: whats the optimal EGT temp for a 2F engine? Been tuning my newly rebuilt 2F and carb and havent been able to figure out why I gradually start overheating at hihgway speeds. I think its a carb issue, but im concerend ill burn...

$750, buyer pays shipping. I have shipped a few of these thru Fastenal. I make a box and put it on a pallet. I have this extra and want to offer it to the community. Professionally rebuilt, magnafluxed, and ready to put on — 2F casting 61031. I will provide paperwork w/ receipt. After the...

I have a 2F short block and rolling assembly. I believe that it’s out of a late 85, early 86 FJ60. I bought it in 21 for a 2FE project that never took off. I saw it run before I bought it. It still has the oil pan, harmonic balancer, fan clutch and I’ll throw in a 2F valve cover. I have had it...

This is a series of technical notes and words of caution on the Tri-mill JTOUTFITTER headers for everyone. -----First of all if you haven't ordered em yet, I woudln't.------ They're a bitch to get on and retrofit compared to other headers, but wanted to give you some additional info and let you...

Hey everyone, I have to admit, I've been hoarding cruiser parts. I didn't want to start my FJ60 restoration until I had every possible part just in case. As a result, my garage has become more of a storage/museum. It's time to let go of some parts and make room to work on the cruiser. Let me...

I am looking for a Cylinder Head casting number 61031 for my 1980 Land Cruiser with 2F Engine.

$750, buyer pays shipping. I have this extra and want to offer it to the community. Rebuilt and ready to put on — 2F casting 61031. Engine this came from was seized so I couldn’t rebuild but found another.; hoping someone can use it. Thanks.

This head was gone through and checked for cracks, can provide receipts; new valve springs, seals etc. All surfaces decked, original valves 400 OBO, buy will pay for shipping, and the crate (25$)

For various reasons, I am moving on from my FJ40 project and looking to first sell the large/heavy stuff before parting out the rest. TLC Performance (fj40jim and crew) rebuilt this 1979 2F engine in early 2022 and was able to ship it to me in August 2022. It has been in a garage the past...

1983 Toyota Land Cruiser FJ45 Pickup 4x4 4speed. This is a GCC spec Cruiser with power steering and a split transfer case. The cruiser was restored before being imported into the US. The color was changed from beige to red. The chassis and cabin were disassembled for cleaning and repainting...

Quite a few of my valve adjustment screws have the lock nut seized, making fine adjustment of the valves impossible. Looking to see if anyone has some laying around rather than paying $8 per from Toyota.

Hey there i made a thread a few weeks ago i have a 1979 fj45 2f Australian. The car was running absolutely beautifully until one day i start her up let the choke off and it would die. I replaced the inline fuel filter and it ran sweet for a day and then it happened again. So it sat for a week or...

Engine, ECU, Harness and wiper motor $2000.00 OBO I am selling my 3FE that I swapped into my FJ60 4 years ago, the motor itself has about probably 270k, I bought the engine as a takeout from another swap from Cruiser Matt after my 2F lost a cylinder. He replaced the bearing on the lower end...

Hi Gents, I'm 26 and just (hopefully) completed my first build+baseline and mechanical journey in general on my 1985 60 series but im hearing some odd engine noises, and a potential crankshaft wobble. I've done everything besides the machining + initial assembling the head and block. I Had my...

This is a 1982 FJ60 carburetor that has had the jets removed. I was present when it was taken off the truck, and watched another guy carefully remove the jets for a project. It is otherwise complete, as seen in the photos. Lots of great parts, or install jets and run it. It has been boxed in my...

The Good Runs great. Drives great. Rides like a dream. Is a Land Cruiser. The Bad Does not look like Megan Fox. Has some rusty bits. Current wife does not appreciate truck's connection to previous wife. Details 1984 FJ60 241,350 miles Stock 2F/H42 4 speed transmission/34mm split T-case Front...

Hey all, The 2F on my 1986 FJ60 decided it was time to go - total loss. Looking for a 2F to replace it with, or any pointers for where to best find one. Ideally seeking one with known mileage and history. Thanks!

I've got a variety of gaskets and other parts I have no need for. Rebuilding your 2f soon? You will need these parts. Selling as a lot but including individual part prices so you know what a good deal you are getting. Prices in red, handwritten on the labels are references from...