1hd-t

Hi there i have a 1991 lc80 with 1HD-T and have been trying to find a supplier for 3" downpipe/dump-pipe/turbo elbow to build my exhaust from, i would prefer stainless steel. 2nd question is what kind of sensors are you guys using for afr reading, and what location do you think is ideal? Also a...

Hey guys, I purchased a diesel cruiser recently and the tach isnt working and upon closer inspection it looks like someone disassembled the cluster and messed with some stuff. Does anyone have a 1hdt/5 speed cluster that up they would be interested in getting rid of? I would also be willing to...

Hi Sourced again some clusters to convert your km/h imported cars into the proper mp/h! Shipping from europe to Conus is around 40$, tracked with EMS. 1. 1HD-FT mp/h manual cluster 330 Eur SOLD 2. 1HD-T? or FT auto cluster 250 eur

Looking for a rust free HDJ80/81 near North Carolina. If you know of any please do let me know. Can fly out far for the right one to drive it back or ship home. 1HD-T or 1HD-FT

Hey Guys I am doing a full rebuild on my 1HD-T engine. Yesterdaay i failed installing the Camshaft and i am trying to figure out what went wrong. So what happend: i placed the camshaft on the cylinder head, block on TDC and puted al the bearings on. i've seted the Torque wrench to 6 Nm (53Lbs)...

I am looking for a 1HDT crossover intake manifold. Looking to delete my aftermarket intercooler. Let me know if you have one around and can part with it. Thanks

I notice there is no gasket there should there be? I'm getting a boost leak around the cap tested with soapy water

I am possibly seeking an upgraded set of injectors and a modified VE pump in the future. how do you choose? how does matching work? what is the process involved to match a set of injectors to a pump?

Hi there My 1HD-T needs a rebuild, the engine builder told me that the connecting rods needs to be replaced, i have a 1HZ engine from a 78 land cruiser in good condition laying around and was wondering if i can take the conrods from that engine. According to the parts catalogue the part numbers...

Hello guys Unfortunately i broke my loved 1HD-T engine on our last highway trip. Short story: Too much power, high exhaust temps leaded to a blown head gasket and 5 of 6 pistons are melted.... Last week we took the engine out and striped it so it is now ready to go to the engine rebuild shop...

Hi As I faced recently how hard is either to get or have them decently priced, I contacted a friend who runs an industrial print company. They can print the different engine decals on high quality heat resistant matterials and price can be quite okay if a I make a larged order. I provide them...

FYI 1PZ, 1HZ, 1HD-T ENGINE REPAIR MANUAL now available in the resources section. https://forum.ih8mud.com/resources/1pz-1hz-1hd-t-engine-repair-manual.144/

Hi, I am in the process of removing injectors and fuel pump from my 1997 1HD-FT to have them rebuilt. In the process, I found a cooper washer and can't find its proper place or find a diagram that refers to it. Please bear with me. Here is the washer beside an injector: I checked on...

Hello folks, I was driving my 80 series today, exited the highway and then went to go back on to the highway and noticed the temp gauge was just on the edge of the red (Maybe slightly into the red). I pulled over immediately and shut the engine off. The coolant reservoir was overflowing a bit...

If you had only those two options, which would you pick, and why? I'm currently living in Japan as a service member, and am about to buy a 1HD-FT Auto cruiser, due to how rare the manuals are. There are a couple 1HD-T 5-Speed's every now and then, and they're expensive. I want a manual, but...

My new to me 1HD-FT shuts down somewhat rough, with the whole vehicle shuddering. I know that this is not uncommon on diesels, and my '96 1KZ-TE used to do same when I reset the ECU, but would go away after about 300-500 km as the engine ECU auto-tuned itself. Is there anything I can do on...

1992 HDJ81 VX Limited Toyota Land Cruiser 1HDT - auto Centre lock/ rear LSD OME lift Turbo back 3” exhaust that sounds great 24v starter Over all good condition! Has some typical 80 series issues Slow windows, shaky side mirror. A few little dings and what not - it’s a 30yr old vehicle...

Cleaning out the parts bin. These are the gaskets at the top of the IP where the fuel pipes connect. Mine was leaking so I sourced these, but it turned out that a little tightening did the trick. They weren't easy to find, so I'm selling them at cost. There are 6 of each. Seats 11176-56010...

I am looking for a CT26 with a good housing that we can rebuild.

I have a 1HD short block for sale. Needs a rebuild. Looks like it's been rebuilt once before a while ago. $950 plus shipping costs. Block is located near Salt Lake City, Utah. I'll have the cylinder head that came on this block in about a week if you're interested in getting both. I also...