I have dicked around with all of these and installed and use them all into different 2F's. I have even seized (doh!) a couple 2F's doing it.. I have run:
- '79 factory dist with OEM ignititer/combo
- FJ60 dist with OEM igniter / combo
- Both of these with mini truck igniter / combo (smaller, less spark (probably) but nice little waterproof unit).
- All sorts of early-mid 70's vaccuum RETARD distributors with points
- A few '69 era aka "NON USA" early vaccuum advance distributor with octane adjusters.
- Prett much all of the different era points distributors (both vaccuum advance and retard) from '69-on with a Crane Cams (similar to pertronix setup) as well as all of them with OEM points, coil, and ballast resistor....
- And finally I tried to modify a HEI from OEM GM to Land Cruiser, basically what DUI does...
Conclusions are: Pin_head is right. We have also discussed this many times before mostly on PBB before mud became big.. It is not size of the spark, it is WHEN. I am not sure if a longer spark makes a difference or not (do not have time to read that thread). But I do know that even though the OEM distributors are good, they are not curved nearly as well, performance wise, as they could be. I have also had all sorts of performance issues mostly with points from distributors with lots of play in the shafts..
My personal favorite is probably the '79 distributor with an OEM igniter / points setp. This is basically the same as a FJ60 but has a smaller head so it is not as much of a hassel using is because you don't have to swap side covers on the engine (but not that big a deal). This is mostly my favorite because it is a bullet proof super bomber OEM Toyota setup.. It is electonic, so no points, and basically super reliable..
Issues I found were:
Both the '79 and the FJ60s are heavily smogged. when using on a desmogged engine this also throws the curve off. So I would send the distributor to Jim C. to have it recurved. Unless things have changed Jim C. will recurve any OEM Toyota distributor. I ran them without the recurve and they did pretty well though, regardless... But I do think more umph could have been pulled out of them....
If I remember correctly from dorky LCML daze, OEM vaccuum advance will only go as high as 12 advanced when Jim C (correct me if I am wrong Jim!) will go up to as high as 17 degrees or something like that. So there is more performance and power to be squeezed out of the OEM dizzies, even the late model...
RE the HEI. I actually think this is a fine unit but I **would not** mess with trying to get the right curve and parts etc on a HEI by yourself. I did this route, spent way too much time and money doing it, and then ended up seizing a perfectly good running '79 2F in a FJ40. I would buy a HEI from DUI, that also has the correct performance curve, better and stronger than really any OEM distributor. I do think slightly hotter spark, combined with the correct advance curve, actually does make a difference. But if you don't have the right curve, it is wasted energy. DUI is not perfect though, if you search PBB, one of their distributors took out Box Rocket's (on PBB) engine and required some major rebuilding work. And DUI **did not** entirely stand behind their product and I believe Box Rocket did have to put up some out of pocket money. this is because, even though the Toy and GM engines share common ancestry, **they are not the same engine***.
In order my preferance is probably:
'69 distributor vaccuum advance with octane adjuster aka "a non-USA" distributor with a Pertonix setup.
'79 OEM distributor with Jim C modified advance curve and OEM or Mini Truck ignitor and coil combo.
FJ60 Distributor with Jim C modified advance curve and OEM or Mini Truck ignitor and coil combo.
DUI HEI distirbutor.
But that said honestly all would probably work well IMO and I would be happy with any of the above setups on a 2F.
This has been years since I have messed with all of this stuff so again Jim C / others please correct me if I'm wrong..
Andre