Wrong grease in knuckles

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 13, 2019
Threads
2
Messages
10
Location
North Carolina
Hi all, I’ve spent hours searching but can’t find a definitive answer. I just bought my first 80 series and am going through it top to bottom. I checked the knuckles for grease and got some less than stellar news- what looks like general purpose red grease was used (leftover moly grease was used at some point in the past as evident by remainder in the plug) and the knuckles don’t seem full to spec.

Heres the question- do I just fill it the rest of the way with moly grease and hope for the best? Is there a reasonable way to flush it out (I’m thinking probably not)? Any advice?
Thanks!
 
Put some moly in there, but don't pack it completely. I wouldn't fret about it too much. Instead of 500,000 miles they are now only going to last 450,000
 
When I bought mine with 165k on it, the knuckles had been serviced similarly by someone with some kind of sticky green grease and just enough to pack the birfs. That led to dry exterior, no film of grease on the smooth round part so it got a bit rusty. I had planned on a front axle service anyway. I just followed the FSM. The birfs survived.
 
Jjt35: add fresh grease, Valvoline Palladium, find it at NAPA stores.
Start with 1/2 14oz tube per side. You want the knuckles to be 2/3 to 3/4 full.

The Red grease is likely Lithium based so no problem if you add another Lithium based grease, color doesn't matter.

While your at it, bypass the stock breather assembly (which doesn't work well) on the top left of the front axle assembly. The purpose is to prevent
grease getting sucked into the axle housing contaminating the gear oil.

Take a three foot section of 1/4" rubber fuel hose and attach it to the pipe nipple (unscrew and clean that out first) and run it up to the engine compartment. Find a small filter to stuff in the open end and zip tie the hose to any bracket.

Welcome to Mud
 
Last edited:
the breathers are more to keep water from sucking into the axles in a water crossing. The temp change from warm driving to cold
water will draw in water. The military vehicles pump air into the breathers on the axles, trans and transfer during water crossings.
The rubber diaphragm and spring in the factory breather cap does an OK job but running it higher doesn't hurt. The more grease in the knuckles the less place for water to reside. Pack it full. Grease won't migrate into the axle.
 
the breathers are more to keep water from sucking into the axles in a water crossing. The temp change from warm driving to cold
water will draw in water.
That is the purpose of the breathers, yes. The purpose of replacing them is that they are often faulty or clogged, which can cause the grease from the knuckle to be pulled into the axle housing. Extending them is added protection from water infiltration.

Pack it full.

Not necessarily a good thing to pack them 'full'. Toyota is very specific about leaving some space in the knuckle and hub.

Grease won't migrate into the axle.
In my experience, some grease will always migrate into the axle. I have never pulled a front axle drain plug and seen clean oil.
 
If it's clean and read sticky lithium based grease you should be good to just top it up with moly grease.
Pack it to 1/2-3/4 full.
Rotating action of the birf and knuckle will push gease into the birf if there's enough grease in the knuckle.
Pack it too full and you'll get excess grease pushing past the wiper seals on the knuckle balls and making a mess
 
Good advice. Just a head's up to correct what someone said above, which is that you can't get grease into the birf from the square plug atop the knuckle. Years ago when you were all still driving Jeeps because you didn't know any better, we wondered about that on Mud. So a day or two before I tore down for a birf repack, I put bright colored grease in through the plug to see if it would end up in the birf. It got in there in just a short amount of driving. So, yes you can lube the birf through the plug.
 
While your at it, bypass the stock breather assembly (which doesn't work well) on the top left of the front axle assembly. The purpose is to prevent grease getting sucked into the axle housing contaminating the gear oil.

Take a three foot section of 1/4" rubber fuel hose and attach it to the pipe nipple (unscrew and clean that out first) and run it up to the engine compartment. Find a small filter to stuff in the open end and zip tie the hose to any bracket.

This is very important, especially if you have oil leaks in the front such as oil pump, dizzy, or front main. I did not realize how low the front breather is placed, and it was sealed by oil/ dust.

The method mentioned above works perfect. But if you want a more "polished" looking option, and want to spend some $, ARB (and others) make a kit.
 
If it's clean and read sticky lithium based grease you should be good to just top it up with moly grease.

I would be weary of mixing greases, regardless if it is "clean" or not. Sometimes greases can react pretty strangely to one another.
 
Been discussed previously; lithium based greases are generally compatible
with each other, color doesn't matter by itself. Some greases are definitely not compatible ie: Bentone (clay) based (very high temp grease used for Industrial applications) and Lithium based, but you're not going to find that grease or most of the other odd grease types at Wallymart or the autoparts store, except for some Marine greases, which may or may not be compatible with a Lithium based grease.

However a Molybdenum fortified Lithium base automotive grease is going
to be compatible with a non-moly automotive grease.

So yeah, in an ideal world it may be better to clean out all old grease and start over (not so much because the old grease is incompatible with the new, but because the old grease likely has grit or other contamination in it), but that's not easy to do with our front axles. If your knuckes/spindle bushings, U-joints, or slip yolk are low on grease, better to have something in there rather than nothing. IMHO.

Here's a link to a grease compatiblity chart:

 
Moly in the knuckles and birf. I would tear down and rebuild with new kit from terrain. The rebuild is easy and fun, just messy. Then you know what you a have in there and you did the job correct. You never know the PO’s job was done right.
 
Like has been said, 1/2 to 3/4 full, but definitely not full to the top.
Needs to be air space in there for heating/cooling expansion/contraction.
The birf chamber doesn't have a vent to re-leave pressure like the diff housing does.
Otherwise, when heated, grease would be forced under high pressure past the axle seal into the diff housing/lube.
Happens a little anyway, but you don't want it forced.

It is said you can read the grease level outside, by looking at the residual goop line on the knuckle balls.
Mine is below 1/2 on the front, above 1/2 in the back, I assume due to forward birf spinning.
 
In my experience, some grease will always migrate into the axle. I have never pulled a front axle drain plug and seen clean oil.

Last time I changed diff lube, after WAY too long, it came out this sick shimmery grey/green swamp ooze.
Molly fortified gear oil :hillbilly:
Nothing wrong though. Vent nice and open. Molly grease still in good shape, so seals are still good.
I just went too long. Moly grease slowly and steadily migrating past the seal into diff housing.
 
When I was doing the knuckle service, I found it was packed with some red wheel bearing grease. It was probably in there for at least 50k miles. I replaced it with Valvoline Multi-Vehicle Moly fortified gray grease (hope that's okay!), and I used a 1 pound tub in each knuckle. I don't think the red grease hurt anything after 50k miles, but I think you should only use a moly grease, and not mix 2 different types of grease. I mean, if you've gotten to this point, you might as well just clean all the red grease out and put fresh moly grease in. Like bambusiero said, don't overfill it because you'll have a mess when the housing/grease heats up.
 
Also - and this is a personal "what do I want to put up with" sort of thing.

I just decided to use the same moly grease for the spindle / wheel bearings as well the birf, instead of trying to keep 2 kinds of grease in there.
There's a theoretical argument that says moly particle enhanced grease is only for slow high pressure sliding things (birf), not high speed roller bearings, and wheel bearing grease shouldn't have that, but practically, wheel bearings aren't really high speed anyway. The idea is that the particles might cause the rollers to slide instead of roll. Nuts. Maybe at some very high content, or a course particle size grade.
I'm convinced that Valvoline Palladium is perfectly fine for both. Very smooth, soft, buttery stuff.
 
Also - and this is a personal "what do I want to put up with" sort of thing.

I just decided to use the same moly grease for the spindle / wheel bearings as well the birf, instead of trying to keep 2 kinds of grease in there.
There's a theoretical argument that says moly particle enhanced grease is only for slow high pressure sliding things (birf), not high speed roller bearings, and wheel bearing grease shouldn't have that, but practically, wheel bearings aren't really high speed anyway. The idea is that the particles might cause the rollers to slide instead of roll. Nuts. Maybe at some very high content, or a course particle size grade.
I'm convinced that Valvoline Palladium is perfectly fine for both. Very smooth, soft, buttery stuff.
I use the same moly-fortified grease on everything. A good man once pointed out to me that if a roller has so little friction that it slides instead of rolling, then what's the problem? No friction equals no wear. In any case, it doesn't work that way, and modern moly-fortified grease is rated for high temp wheel bearing applications anyway.
 
its more important to make sure that theres grease in the knuckle, ive topped mine off with whatever we had in parts for the greases guns with no ill affect for the last 7-8 years. if the knuckles are dry than filling them will take about 1 1/2 tubes from the grease gun, if your disassembling than about 1 1lb tub per side is about right
 
Back
Top Bottom