Which drive belt is missing here?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 3, 2005
Threads
79
Messages
653
Location
Centennial, CO
My wife was driving and heard what she described as running over tractor trailer tires that came off.

I checked the tires out when I got home and they looked fine, so I backed it out to work on my car in the garage and then I heard the sound.

Sure enough it was a belt that disentegrated and got wrapped around the fan axle.

Since I have no idea how big it was I don't have the option of comparing it to one at NAPA so I want to get as exact as I can with it.

Can anyone tell me which one is missing here?
IMG_2118-med.JPG
 
There should be 2 side by side there, same size, same routing.

My wife was driving and heard what she described as running over tractor trailer tires that came off.

I checked the tires out when I got home and they looked fine, so I backed it out to work on my car in the garage and then I heard the sound.

Sure enough it was a belt that disentegrated and got wrapped around the fan axle.

Since I have no idea how big it was I don't have the option of comparing it to one at NAPA so I want to get as exact as I can with it.

Can anyone tell me which one is missing here?
IMG_2118-med.JPG
 
Thanks WFD175, that makes it much easier. I can take the other one off and just get a match. Great!
 
Thanks WFD175, that makes it much easier. I can take the other one off and just get a match. Great!

If you don't know this yet, attack it from the bottom, it's much easier. (takes about 30 minutes the 1st time)

Remove the shield under the front portion of the motor, lube up the adjusters on the alternator, (for the 2 belts) and the adjuster on the single short "under-belt" . I needed a hinged gear wrench to get the alternator adjuster loose.

Also, they do come in pairs as a matched set OEM Toyota. An unmatched pair may have caused the problem in the 1st place.
 
I would suggest replace both if you can .. and even can keep one as spare .. just to make sure both have the same leght ( not one more long than other for the use )
 
If you don't know this yet, attack it from the bottom, it's much easier. (takes about 30 minutes the 1st time)

Remove the shield under the front portion of the motor.


Not sure about the other years, but my 97 has access holes on the shield, so all I needed was a long extension to loosen the A/C tensioner :cool:
 
Not sure about the other years, but my 97 has access holes on the shield, so all I needed was a long extension to loosen the A/C tensioner :cool:

I just changed my belts last week, so it's still fresh in my mind.

The a/c "tensioning" bolt on my 96 faces out towards the battery (perp to the ground), the "set screw "(bolt) also perp to the ground on the square "slide" faces forward. Nothing faces downwards. The only way I could see to get to them in my case is to remove the shield. It's 4 easy bolts and snakes rather easy above the steering stabilizer.

I had to get my state inspection 2 weeks ago, so I inquired about the belt change. The dealer wanted to charge me 1.5 ($99/hr) hours to do it. I told him about the 25 minute method and he said no way.

I'm now $150 closer to rear armor.
 
I just changed my belts last week, so it's still fresh in my mind.

The a/c "tensioning" bolt on my 96 faces out towards the battery (perp to the ground), the "set screw "(bolt) also perp to the ground on the square "slide" faces forward. Nothing faces downwards. The only way I could see to get to them in my case is to remove the shield. It's 4 easy bolts and snakes rather easy above the steering stabilizer.



That's odd :confused:

Here's a link to IdahoDoug's 25 minute belt change thread:


https://forum.ih8mud.com/80-series-...belts-25-minutes-post2682018.html#post2682018


First, loosen the lock bolt in the center of the A/C tensioner pulley. It's a 14mm and I find it easiest reached standing with the left foot in the engine bay and right foot on the bumper. Lean way down with an open end wrench, bracing yourself on the valve cover with your left hand. Just loosening a revolution will do.
Then slide under the truck with a 14mm on about a foot of extension and find the 1" hole under the AC compressor. Directly in line with it is the tensioner bolt - a very long bolt. Turn it counter clockwise until it comes loose and then insert it for a revolution or two.


It's been a while, but that's what I remember doing in a parking lot in the dead of the night and I didn't have to drop the shield :meh:
 
Great advice all around. Thanks.

I'll definitely hit up the dealer in the morning and get the OEM belts. I just changed the belts on my 60 in April, so it will be a good 60 vs. 80 comparison. If I can do it in less than 3 hours it will be easier.

I love my 60, but I have to say, they really made the 80 well.

-Winston
 
Great advice all around. Thanks.

I'll definitely hit up the dealer in the morning and get the OEM belts. I just changed the belts on my 60 in April, so it will be a good 60 vs. 80 comparison. If I can do it in less than 3 hours it will be easier.

I love my 60, but I have to say, they really made the 80 well.

-Winston

If you want pain, change FJ62 belts. Total PIA. The 80 is easy in comparison. Get the matched belts from Toyota, Install and be happy.
 
Great advice all around. Thanks.

I'll definitely hit up the dealer in the morning and get the OEM belts. I just changed the belts on my 60 in April, so it will be a good 60 vs. 80 comparison. If I can do it in less than 3 hours it will be easier.

I love my 60, but I have to say, they really made the 80 well.

-Winston

Just make note of how the belts do not go around the idler pulley. Some people have actually routed the belts around it, whcih will cause problems.
 
And this is why 80s rock. What other vehicle out there has dual fan belts as a back up? Had you only had one belt to begin with, you'd be posting about an overheated engine and how to replace a headgasket.
 
And this is why 80s rock. What other vehicle out there has dual fan belts as a back up? Had you only had one belt to begin with, you'd be posting about an overheated engine and how to replace a headgasket.


I wouldn't exactly call the double belt a backup :o

With mine, when the front belt snapped, it took the second one with it :doh:

My backup is two new belts in the toolbox ;)
 
Well, having the two belts, distributes the load that would normally be taking up by one belt, along two belts equally. It makes sense that under normal circumstances, both belts would fail at the same time, since both belts should wear equally. But the wear should take twice as long as a single belt.

So, rather than backup, maybe it's more accurate to say, the dual belt is a longevity thing.
 
Well the belt replacement really wasn't too bad. I took my time with it to make sure I got it in correctly and nice and tight, but this should be a 30-60 minute job.

The part that was a real PITA was the alternator tightening bolt. That thing is hard to get to from the top and bottom. I skinned my knuckles, but got er done.

Thanks for the great posts, guys.
 
You are lucky

That you don't have a Diesel 80 with dual batteries and a Safari intercooler. If you thought that things were tight on a petrol 80 then on my truck belt changes are like keyhole micro surgery. Loosing skin is mandatory and swearing at the whole thing makes it all that little bit easier. Removing the fan blade assembly from the clutch sometimes allows a bit more room for access.
Generaly it is a huge PITA but patience evebtually triumphs.
 
PITA or not, it's best to change the belts before one or both break and leave you on the side of the road...doing the repairs when it's not nearly as convenient...


:D
 
Back
Top Bottom