Warn Panhard Causing Death Wobble?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2004
Threads
178
Messages
1,417
Location
Athol, MA
Worn Panhard Causing Death Wobble?

I've been chasing and fixing vibrations and a front-end wobble. I cured the pulsing in my brake pedal with all new OEM rotors, 100 series front pads, OEM 80 series rear pads, rebuilt calipers, new LSPV and modified bracket. I still have a death wobble that I believe is being caused by a loose panhard bolt. Will this cause the dreaded "Death Wobble"?
Pan Hard Bar 001.webp
 
Last edited:
I tried to tighten it, but I think the best option is to remove it, replace the bushing and bolt and then make sure it is torqued to spec. Which brings up another question..... How do I get on the nut that is on the backside of this bolt?
 
Great advice Rick, but..... and a big but.... I just looked at a spare axle I have in the garage and saw that this nut is in fact is "Supposed" to be captured. Well, the reality is that the one on my truck that is loose is no longer captured. The weld on the nut must have failed. Now what??? Help....
Pan Hard Bar 005.webp
Pan Hard Bar 003.webp
 
I can't be the one and onle person that has had this happen to? I'm hoping for a better solution than having to cut off my bad bracket and replace it with the good one I have in the garage. Then again the right way to fix this is probably to cut off the old bracket, clean the area and weld on a new nut. Boy, this isn't going to be fun....
 
my first thought would be to drill 2 small holes through the back plate half off the edge of the nut. Then thread the nut onto the bolt to hold it in place and weld through the holes to fasten the nut back into place. You would then have to grind the top of the weld flush with the plate.

I've never tried anything like this but if after some more thought if I couldn't come up with anything better I'd give it a go.
 
Warn Panhard

Looking at the wear pattern under the bolt head I think that tightening it will not solve the problem. It looks like the hole for the outboard end of the bolt has worn out to be larger than it should be. The bolt should be a snug fit in the hole almost to the point of tight so that it cannot move sideways. The bolt should not have warn as it should be harder than the bracket. You will have to get the nut captive again somehow. Maybe a clever welder while it is still fixed to the axle or cut it off and have it repaired and rewelded to the axle.

Have fun
 
Is their enough room to wedge a screwdriver, wrench or scrap thrown in to help keep the nut from turning while hitting it with an impact? If not a welding machine might be able to be used to thrown a bead or slag in their.
 
If the bolt is warn, no big deal... If I can get it off. If the hole is wallowed out then that is a different story all together. The bolt is the factory OEM bolt and was removed and replaced after the panhard was modified when I did my lift. I was able to get the end of a combination wrench in there, sort of. The issue was that I didn't have the correct, 21mm I think, combination wrench and I didn't want to risk rounding off the nut, so I didn't mess with it too much.

If I can get a good enough grip on the nut to remove the bolt that is half the battle.

Let's assume the worst, that the hole is wallowed out and that I will have to recapture the nut again.

To fix the wallowed out hole I can use the bracket off my spare axle. Cut out what I need in the old bracket and the same on the donor bracket. Weld in place and that hole is fixed. No great loss as the axle housing is bent anyway. The method that I'm thinking of is to locate the center of the bolt holes perfectly.... Or as close as possible. Tack weld a piece of square steel over the hole so I can transfer the vertical and horizontal locating lines from the hole onto the patch tack welded over the hole. Once the center is located then I would use the largest possible hole saw to cut out a perfect circular plug to weld onto the damaged bracket. The tacked on piece would be required for the hole saw center drill bit to locate the saw. Do this on the front and back and re-weld a new nut on the back.

Does this sound feesible or am I better off just attacking the donor axle with my cut-off wheel and grinding the whole bracket off? I know either was is going to be a real pain.
 
I am curious as to what else is in that state of rust and wear? Have you checked everything in terms of brackets for TREs, etc? It sounds like you have, but wowza...I am not used to that sort of rust and wear I guess?
 
. I still have a death wobble that I believe is being caused by a loose panhard bolt. Will this cause the dreaded "Death Wobble"?

Yes, I have had a loose panhard bolt cause 'death wobble'. I realize you're already looking at this, just wanted to confirm that it's probably your problem. I don't have any better ideas for removing the old bolt nor fixing the nut. :frown:

-Spike
 
if the hole is wallowed out how about just welding a washer on the bracket.

That's what I would do. There is no reason to cut off the old bracket and re-weld. Even if you took some 1/4 and drilled the correct sized hole in it would be preferable to cutting that bracket off, and maybe even better.
 
This is close to my final plan once I am able to remove the stock bolt and nut.

Order a new OEM bolt.

Find a washer that is a perfect, tight fit to the bolt. If I can't find a washer that is a very tight fit I will have a plate made at a machine shop that is a perfect fit to the bolt. Weld this onto the front most plate.

To recapture a new nut is a bit more complex. I like LandTanks idea of drilling holes and plug welding, then grinding these welds smooth. My concern is having the room to drill at a 90 degree angle. I may have to drill through the outer plate first and then use an extention on my drill bit to drill the holes for the welds through the back plate. The holes in the front plate would be covered by the washer that is welded on.
Pan Hard Bar 004.webp
 
Revised ideas after looking at the bracket. I really don't want to do this a second time so this is my revised plan:

Heat up and bend the front plate out of the way.

Make two vertical cuts down each side of the back plate and bend it forward so I can get good access to that pesky nut.

Like so.
Pan Hard Bar 009.webp
 
Once I have the OEM bolt in hand I will find the correct fine thread nut. I will also buy a shorter bolt so I can tighten the nut down and it will be located correctly in relationship to the hole. Then I can weld the nut with more than the two small factory spot welds. I would use Rick's idea, but I think once the bolt is out and the panhard bar removed the nut will no longer be in the correct position. I don't know that I will even be able to keep it from falling to where I may not be able to get at it.

Bend the back plate back into place and weld up where the cuts were made.

Heat the front plate and bend it back into place.

Weld on the piece of bracket in the picture that I cut off my spare axle housing onto my current bracket if the hole has wallowed out. I like using this better than the washer as it is thicker and I know the hole will be the correct size.
Pan Hard Bar 008.webp
 
Last edited:
Any advice? Will I be compromising any strength with these cuts, bends, and welding?
 
Back
Top Bottom