V-8 Ideas

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 18, 2005
Threads
7
Messages
18
I'm in the process of a frame up rebuild on my '65 FJ-40. The truck has a Chevy 307 V-8. Based on the engine number it looks like the motor is actually a 283 that has been stroked. From what I have read, this appears to be an ideal motor for a cruiser since the 307 was created for higher low-end torque and better fuel mileage. Also, the 283 has a higher nickel content which should wear better than the 307 blocks.

So based on this, is this a better motor than a 350 for a landcruiser? I wanted to see what folks thought about this set-up. Thanks.
 
I have a 327, But like the 283, they are getting tired, I would go with a 350 if I had to do it again, Buy a crate motor from GM with fuel injection of some sort. My 327 had great low end but I think FI would be a better choice as well as a newer motor.
Good luck
 
307 created for torque? Not with a 3.25 inch stroke. If having to pick something in the lower cubic inch range I would use a 305 over a 307 without hesitation. The 307 was developed as a "smog" engine so as to run cleaner but I have to rank it among the worst performance motors GM ever produced.

Best plan ... just as the others have mentioned, a 350 crate motor.
 
looking at my books . 283 and 307 have . the same bore different stroke . longer stroke make's better torque . shorter stroke for a higher rpm .more horses less torque . the 350 .will out torque
any 307 . or 283 these 2 engines have a shorter stroke . you could use your 307 crank in a 350 block to get a 327 . still not as torquey as the 350 . 305 and 350 use same stroke . so a 305 should produce slightly more torque than the 283 or 307 also depends on cam choice . anyways just reading some charts . the 350 rocks .
 
Would you see much difference in gas mileage between a 305 and a 350?
I've been leaning towards using a 305 in my soon to be DD but I have an excellent 350 4 bolt sitting on a stand in my garage...
I didn't think there would be a major difference in stock power between them but from this post I'm begining to wonder!
I'm running a T350 trans too if that makes a difference.

Is a 350 version FJ 40 really THAT much nicer to drive???

I've read that the biggest issue with the 307 is a poor quality camshaft that easily flattens the lobes and makes the engine a real pig.
Some headwork, a quality aftermarket camshaft (think mild...small motor!) and an aluminum 4 barrel intake supposedly wakes them up nicely...but I guess the torque would still be down compared to a 305/350 setup.

Still...if you own it and want to juice it up a little...the parts can always swap over to a 350 later if you decide to go that route sometime in the future.
 
Sculpin.
I dont thing the milage will differ much, What I think is helpfull is how much right foot are you use to using? However Fuel injection is a great way to help economy, as well as gearing. I have a 327 with a stock 3 speed trans...Horrible milage, But I have a NV4500 waiting for install, This will greatly improve the highway RPM's. Getting back to your question, It all depends on what the engine has on the inside's, What head's, Cam, compresion...the like
Have fun
 
I have ran carbureted 327 and 350 V8’s in my 40’s in the past. I have also run 305 and 383 Tune Port Fuel Injected V8’s.

Bottom line pound for pound the 383 TPI beats them all. (However HP the 350 felt real close!) Ok yes bigger displacement but the torque and smoothness of the FI makes me a better driver than I am in the rocks. There is a huge difference between the 305 and 383. I agree with Brian on fuel economy its in how you drive it. If you need fuel economy the #1 way to gain than is in the gearing.

If you have a good 350 I would run it over the 307.

Mark
383 tpi por.webp
 
It's real easy to over carburate a 305 and make it run boggy with crappy milage. I run a 305/th350 and must admit a tbi350 would be much better and much more forgiving.
 
Thanks for the information. The motor I have is a 283 block with 327 heads and 2 bbl 307 intake manifold. I'm not sure what the cam is, but I don't think it's stock. I'm also not sure what kind of crank.

Based on the comments so far, the 350 appears to be a better choice than the 307. Actually, it seems anything is better than the 307. If I were to go with a 350, what year would you recommend? Also, how much would fuel injection cost over carburetion?
 
Another option you might consider is going to a 350 Vortec motor from a wrecked truck/surburban. Get the complete motor with the wiring and all accessories.
 
BernieB said:
how much would fuel injection cost over carburetion?
New aftermarket FI can run anywhere from $800.00 to a few thousand dollars, Getting all in one at a salvege yard would be nice.
Good luck again
 
hey helocat you got any photos from the front or top? i would like to see, got a few ideas running through my head. thanks
 
Back
Top Bottom