Using 4 wheel drive

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 2, 2005
Threads
18
Messages
141
This is probably the dumbest post you guys have seen in a while, but I want to make sure I do not screw anything up. Say I want to stick it in 4 wheel drive. I get out, engage the hubs (I have "Selecto" hubs on the front), get back in and then put the transfer case in 4 low or 4 hi. Say I need to hit a short road to another trail and I want to put it back in 2 wheel drive. Can I just put the transfer case into 2 hi and not disengage the hubs? Or will that mess something up? What if I don't need 4 wheel drive but just need lower gearing for a minute, can I put it into 4 low and not engage the hubs? I need to get a book on 4x4 basics so I can learn a bit more about driving off road. I know the basics of off-roading, I just don't know the proper procedures for using the 4 wheel drive.

Again, sorry for the stupid questions, but I have never had a Land Cruiser (or 4x4 for that matter) and want to use it the way it was intended instead of abusing it.

Has anybody put together a list of tools to take on trips, along with other necessary things?
 
step 1: where are you? a trip out with a local club will do wonders....likely 10x any knowledge you can pull from a post here....

2wd for all road situations....hubs locked in 2wd won't hurt anything, but may effect steering slightly. Not all rigs drive well that way, and to eliminate wear, I tend to take the 15 seconds it requires to get out and unlock, even for short road trips.

4wd high for low traction stuff, and some speed...like 45mph maybe (again, rig dependant)....snow is the biggest use for this.

4wd low for low traction low speed stuff, like anytime you are offroad. I had mine modded for 2wd low, and would constantly switch from 2 to 4 and back...anytime I even thought I'd need 4wd, I'd shift in, to minimize impact on the trails. Without that mod, leave it in 4wd low and take your time.

IMO, it IS worth the effort to unlock hubs for road use....if nothing else, good excuse to teach the SO how :D
 
never hurt me. i think it would be fine for short distances
 
You do have to stop the Cruiser before switching between 4 hi and 4 low, right?
 
honestly, with the hubs locked in, and assuming there is no speed difference between front and rear, you can "shift on the fly" in hi range.... (ie: pavement)

however, if the rear is spinning/stuck and you shift, you might get to replace a t-case instead (ie: mud)
 
72FJ40LandCruiser said:
Has anybody put together a list of tools to take on trips, along with other necessary things?

This really depends on your mechanical abilities and experience. Also what kind of wheeling you will do.

A good (Craftsman) basic wrench and ratchet set (metric if stock, standard if you have a V8 or lots of add on goodies with standard hardware) as well as screw drivers and pliers, inluding vice grips.

Hammer.

Lug wrench and a highlift jack (this will get you out being stuck, not only changing a flat).

Spare oil and filter and a fuel filter.

Tow strap, chain, shacles, etc.

If you are doing harder trails you may want to carry a socket and pliers for changing a birfield, as well as a spare birf. If your pretty stock and do easier trails, you won't need it.

Some clubs make up standard lists of tools and parts. Like Woody said, find other cruiser heads in your area and wheel with them. Thats you best bet.
 
its good to drive slow (under30-40) with hubs in once a month it will lube all the front end parts...
 
woody said:
I had mine modded for 2wd low, and would constantly switch from 2 to 4 and back...anytime I even thought I'd need 4wd, I'd shift in, to minimize impact on the trails. Without that mod, leave it in 4wd low and take your time.

If you are not familiar w/ the 2-Lo mod (not to be confused w/ the J-Lo mod), it is awesome.

I assume you are talkingabout a '72 40? So your t-case linkage is probably different than mine, but all I had to do for my '78 40 is notch the bracket and SHAZAM! Lo range in 2WD...

A pic of my modified bracket:

attachment.php
 
as for the hubs, don't sweat it, mine have been stuck in the locked position for 2 years and they see 300 miles a week on tarmac. so you don't have to jump out all the time.

take the time to do the low 2 mod... it rocks. and you never have to unlock your front hubs again
 
Ah, a chance to ask my own dumb question - On older rigs with the vacuum 2-4WD shifter, can it be run in 2 Lo just by leaving the vacuum shift in the 2WD position and shifting the dash lever? The manual doesn't say it can, but it doesn't say it can't, either. Pablo's linkage mod just looks like it cuts out the plate that blocks the linkage from disengaging front while in low, and the oldies just have those functions separated.

I'm ignorant because mine has never been running while I've known it, and is currently scattered across the garage (but I'm making progress!) "Driveline complete by August" is my mantra.
 
additional to pablo's linkage mod you can just remove the whole plate
that he notched...
 
Back
Top Bottom